Henny Penny OFG-390 manual Factory Presets F/C, Gas/Electric, Speaker Volume

Page 41

		Model OFG- 390
3-16. SPECIAL PROGRAM MODE
(Continued)	Factory Presets (F/C, Gas/Electric, Speaker Volume,
	Speaker Frequency, Codes, Initialize System)
	1.	Press and hold the FUNCTION button for two seconds until
		“REG PROGRAM” shows in the display. As soon as
		“REG PROGRAM” shows in the display, press and release
		the FUNCTION button 3 times until “FAC PRESET” shows
		in the display.
	2.	When “CODE” shows on the display, enter 2957. “DEG”
		and “MODE” flashes in the display. Press any of the product
		buttons to toggle from ºF to ºC, and vice versa.
	3.	Press and release the FUNCTION button and “TYPE”
		and “FRYR” flashes in the display. Press any of the product
		buttons to toggle from “GAS” to “ELEC”, or vice versa.
	4.	Press and release the FUNCTION button twice, and
		“SPKR” and “VOL” flashes in the display. The volume can
		be changed from 01 to 10, 10 being the loudest.
	5.	Press and release the FUNCTION button 3 times, and
		“SPKR” and “FREQ” will flash in the display. The frequency
		can be set from 100 to 2000.
	6.	Press and release the FUNCTION button 10 times, and
		“INITIALIZE SYSTEM” scrolls across the display. Press

and hold any of the product buttons and the display will count down from 5. Once the display counts down, release the product button, and the control will set factory preset param- eters into the controls.

Before attempting to change the other modes in the Factory

Preset Mode, please call the Henny Penny Technical Service

Department at 1-800-417-8405, or 1-937-456-8405.

703

3-19

Image 41

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Henny Penny Head GAS Open Fryer SpecificationsTable of Contents Assistance IntroductionProper Care Hazardous Situation WHICH, if not SafetyAVOIDED, will Result in Death or Serious InjuryPage Unpacking Instructions InstallationUnpacking Remove the counterweights from the pallet, which areInstructions Strapped to the pallet, under the fryerOptional Ramp Unloading Model OFG 908 Selecting Position and install fryer to prevent tipping or moveLocation Ment. Restraining ties may be used for stabilizationGAS Supply Ventilation of FryerFryer must be isolated from the gas supply piping During any pressure testing of the gas supply pipingSystem by closing its individual manual shutoff valve System at test pressures equal to or less than 1/2Model OFG 303 GAS Pressure Regulator SettingGAS Leak Test Requirements ElectricalModel OFG Page Operation Operating Components High Limit Airflow SwitchIgnition Modules Spark IgnitorsIndicators SwitchesLID Operation Melt CycleAlthough the Displaywillread Cool Switches IndicatorsDuring the Standby MODE, the Shorten ING is HOT and will Cause BurnsSMS Controls Filling or Adding Shortening Basic Operation Cool Which could Result in Serious Burns Care ShorteningPersonal INJURY, FIRE, AND/OR Property With Prolonged USE, the FlashpointFiltering of Shortening Turn COOK/PUMP switch to OFF positionSHORTENING, IT’S Possible That the Filter Cloth or Glove When TighteningConnection AT the Union on the Filter Tube is not Tightened PROPERLY. if SOLightingand Shutdown of the Burners Cleaning the Frypot Regular Maintenance ResetFilter Pump Motor PROTECTOR-MANUALLubricating Lid Rollers -Annually Preventive MaintenanceCleaning the Nylatrons Monthly Maintenanc PreventiveCode ProgrammingAfter the proportional control, press and release Reset Usage Special Program ModeProgramming Review UsageSpeaker Frequency, Codes, Initialize System Factory Presets F/C, Gas/Electric, Speaker VolumeAppliance Test Tech I/O ModeMode Special ProgramHeat Control Problem Cause Correction Troubleshooting Trouble Shooting GuideDisplay Cause Panel Board Correction Error Codes303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised