NOTE: To exit without saving changes, press WATER/ICE at any time while in adjust mode, or allow about 60 seconds of inactivity and adjust mode will turn off automatically.
When adjusting temperature set points, use the following chart as a guide.
CONDITION: | TEMPERATURE |
| ADJUSTMENT: |
REFRIGERATOR too cold | REFRIGERATOR Setting |
| 1° higher |
REFRIGERATOR too warm | REFRIGERATOR Setting |
| 1° lower |
FREEZERtoo cold | FREEZER Setting |
| 1° higher |
FREEZERtoo warm / | FREEZER Setting |
Too little ice | 1° lower |
The set point range for the refrigerator is 33°F to 45°F (0°C to 7°C). The set point range for the freezer is
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is turned off.
•To turn cooling off, press and hold the LOCI( and MEASURED FILL buttons at the same time for 3 seconds.
IMPORTANT: To avoid unintentionally locking the dispenser or changing other settings, be sure to press both buttons at exactly the same time.
When cooling is off, "COOLING OFF" will appear on the display screen.
Press and hold LOCI( and MEASURED FILL for 3 seconds again to turn cooling back on.
Additional Features
Accelerated Ice Production
The Accelerated Ice feature assists with temporary periods of heavy ice usage by increasing ice production.
IMPORTANT: This feature only works if the ice maker is turned on. See "Ice Maker and Storage Bin."
•To turn on the feature, press SETTINGS then TEMPERATURE. When the feature is on, the Accelerated Ice icon will appear on the dispenser display screen.
- _ Acceler
- _ Ice
The Accelerated Ice setting will remain on for a minimum of 90 minutes unless manually turned off.
To manually turn off the feature, press SETTINGS then TEMPERATURE again, or adjust the freezer temperature set point. The Accelerated Ice icon will disappear when the feature is off.
NOTE: If increased ice production is desired at all times, change the freezer set point to a lower setting. Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the refrigerator or freezer door is open for 5 minutes and the product cooling is turned on. The alarm will repeat every
2 minutes. Close both doors to turn it off. The feature then resets
and will reactivate when either door is left open again for 5 minutes.
NOTE: To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.
m
Disabling Sounds
•To turn off all dispenser and control sounds, press and hold WATER/ICE and MEASURED FILL at the same time for
3 seconds.
IMPORTANT: To avoid unintentionally changing other settings, be sure to press both buttons at exactly the same time.
To turn all sounds back on, press and hold WATER/ICE and MEASURED FILL at the same time for 3 seconds again.
IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Use a sturdy container to depress and hold the water dispenser pad for
5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.
NOTES:
•The dispensing system will not operate when the freezer door is open.
•Allow 24 hours for the refrigerator to cool down and chill water.
Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Wait 72 hours for full ice production.
The display screen on the dispenser control panel will turn off automatically and enter "sleep" mode when the control buttons and dispenser pad have not been used for 2 minutes or more. While in "sleep" mode, the first press of a control button will only reactivate the display screen, without changing any settings. After reactivation, changes to any settings can then be made. If no changes are made within 2 minutes, the display will
17