Shindaiwa 89309 Starting the Engine, Before starting the engine, Make sure you have a secure

Page 7

Starting the Engine

Before starting the engine

This unit comes completely asembled.

Ŷ This user manual

Before using this product, please make

Ŷ Tol kit including combination spark

sure you have all the components

plug/13mm wrench

required for a complete unit. Carefully

Ŷ Blade protecter

inspect all components for damage.

 

Starting the Engine

IMPORTANT!

 

IMPORTANT!

The terms “left,” “left-hand,” and “LH”; “right,” “right-hand,” and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation of this product.

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP.

WARNING!

KEEP CLEAR OF THE CUT- TING ATTACHMENT DURING START- ING OPERATIONS! THE CUTTERS MAY

WARNING!

Never start the engine from the operating position.

The cutting attachment will move when the engine accelerates!

MOVE WHEN THE ENGINE IS STARTED!

ŶPlace the trimmer on the ground during all starting operations.

ŶMake sure you have a secure

IRRWLQJDQGNHHSD¿UPJULSRQ the unit as well.

ŶKeep all bystanders and pets well clear of the trimmer during starting operations.

1.Slide the ignition switch to the “ON” position.

2.Set the throttle lever to the “fast idle”:

a.Depress and hold the throttle lock, then squeeze the throttle lever toward the handgrip on the shaft tube.

b.Depress and hold the fast idle button.

c.While depressing the fast idle but- ton, release the throttle trigger.

3.Press the primer bulb until fuel can be seen flowing in the transparent return tube.

IMPORTANT!

START

On/Off Switch

Throttle interlock

Fast Idle

Throttlebutton trigger

Slide the ignition switch to the ON postion

Choke closed

Primer bulb

Return Tube

Press the primer bulb

Hold the unit

¿UPO\Make sure the cutters are clear of obstructions!

.Pull recoil

starter handle

upward

The primer system only pushes fuel through the carburetor. Repeatedly press- ing the primer bulb will not flood the engine with fuel.

Set the choke lever to the CLOSED position if

Start the trimmer by pulling the starting

engine is cold

handle rapidly outward

 

4.Set the choke lever to the CLOSED position if engine is cold.

5.Place the unit on the ground. Grip the engine cover with your left hand and the starter handle with your right hand (shown).

6.Pull the starter handle slowly toward you until you feel the starter mecha- nism engage.

7.Start the trimmer by pulling the start- ing handle rapidly outward.

CAUTION!

The recoil starter can be easily dam- aged by abuse! Never pull the starter cord to its full length.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. Refer to the “Starting a Flooded Engine” section of this manual.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents HT231 Hedge Trimmer Safety and operation labels ContentsIntroduction Stay Alert SafetySafety devices and labels Work SafelyWipe off any fuel that may have To the unit Spilled Operating the Hedge TrimmerRPM without a load. Doing so could It free of loose vegetation, mud, etcDo not alter this machine or any of its components Product DescriptionMinimize the Risk of Fire Mixing fuelFilling the fuel tank Examples of 501 mixing quantitiesMake sure you have a secure Starting the EngineBefore starting the engine Starting the EngineStopping the engine Adjusting engine idleOperation Spark Plug MaintenanceGeneral maintenance Daily maintenance10 15 hour maintenance Hour maintenanceEvery 20 and 100 hours Often in dusty or dirty conditions Throttle free play adjustmentCutter blade adjustment Every 50 hours of operation moreSult your servicing dealer Long Term StorageRemove the spark arrester screen For carbon buildupPossible Cause Troubleshooting GuideEngine does not Start What To CheckEngine is knocking LOW PowerIs the engine overheating? Operate at slower rateAdditional Problems Emission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan ¡ADVERTENCIA Cortasetos HT231Etiquetas informativas sobre seguridad y funcionamiento IntroducciónContenido Declaraciones De SeguridadEtiquetas de seguridad SeguridadTrabaje con cuidado Mantengase AlertaPrecauciones de operaciones Seguridad continuaciónDe hierba, barro, etc Vshflàfdflrqhv Descripción del ProductoAdvertencia Mezcla de CombustibleLlenando el Tanque de Combustible PrecauciónAntes de usarla Arranque del motorArranque del motor Operación Arranque del motor continuaciónParada del Motor Ajuste de la Marcha MínimaBujía MantenimientoMantenimiento generale SilenciadorMantenimiento cada 10 horas Mantenimiento continuaciónCada 20 y 100 horas Retire y reemplace el elemento del filtro Mantenimiento cada 50 horasCuchillas Más frecuente en condiciones polvorientas o adversasAlmacenamiento de Largo Plazo Mantenimiento cada 139 horasPosible causa Guia DiagnosticoEL Motor no Arranca Qué revisarDepósitos de carbonilla en el pistón o el silenciador Guia Diagnostico continuaciónBaja Potencia ¿Se sobrecalienta el motor?Otros Problemas Que Está Cubierto Por Esta Garantía Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Cobertura de la Garantía del FabricanteRemarques SP18 SP19 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Avertissement TAILLE-HAIE À Lame HT231Mise EN Garde Table des MatièresMises en garde Étiquettes au fonctionnement et à la sécuritéSécurité au travail SécuritéÉtiquettes de sécurité Sécurité suite Maintien prévu recommandé Ment serré avant toute utilisationCaractéristiques techniques NomenclatureRéduire les risques d’incendie Mélange de carburantRemplissage du réservoir à carburant Exemples de quantités de mélange de carburant àAvant démarrage Démarrage du moteurDémarrage du moteur Utilisation Démarrage du moteur suiteArrêt du moteur Réglage du ralenti du moteurEntretien Toutes les 20 et 100 heures d’utilisation Entretien suiteEntretien aux 10 heures Toutes les 10 à 15 heures d’utilisationRéglage de la lame Remplacement du filtre à carburantEntretien aux 50 heures Le jeu du levier d’accélérateurEntretien aux 139 heures Remisage à long termePoints à contrôler SolutionGuide de dépannage LE Moteur NE Démarre PASLe moteur cogne Guide de dépannage suitePuissance Insuffisante Le moteur surchauffe-t-il ?Autres Problèmes Couverture de la garantie La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie des fabricantsFR17 FR18 FR19

89309 specifications

Shindaiwa 89309 is a high-performance trimmer head designed for both professional landscapers and avid gardeners who demand reliability, efficiency, and ease of use. This product stands out in a crowded market due to its innovative engineering and robust construction, making it an essential tool for those who take lawn care seriously.

One of the main features of the Shindaiwa 89309 is its durable design. Constructed from high-quality materials, it is built to withstand the rigors of everyday use while maintaining optimal performance. This means users can tackle tough tasks without the fear of wear and tear, ensuring longevity and durability.

The trimmer head integrates advanced technologies to improve efficiency and ease of operation. One of its most notable technologies is the easy-loading spool system, which allows users to quickly and effortlessly reload the line. This feature significantly reduces downtime, enabling users to get back to their work without hassle.

Additionally, the Shindaiwa 89309 is designed with a dual-line cutting system, which enhances its cutting performance. This system provides a wider cutting path, allowing users to cover more ground in less time. The trimmer head delivers clean and precise cuts, ultimately resulting in a neater finish for lawns and gardens.

Another key characteristic of the Shindaiwa 89309 is its compatibility. The trimmer head works seamlessly with various Shindaiwa machines, allowing for versatility and ease of integration into existing tool collections. This adaptability makes it a practical choice for professionals with multiple pieces of equipment.

Moreover, the Shindaiwa 89309 features an efficient balance that reduces user fatigue. The lightweight design combined with a well-thought-out weight distribution allows for extended periods of use without straining the operator, which is crucial in a demanding work environment.

In summary, the Shindaiwa 89309 trimmer head embodies the perfect blend of durability, efficiency, and user-friendly features. Its advanced technologies, including the easy-loading spool and dual-line cutting system, make it an invaluable tool for achieving pristine landscaping results. Whether for professional use or personal projects, the Shindaiwa 89309 stands out as a reliable choice for trimmers and gardeners alike.
Top Page Image Contents