Shindaiwa 89309 manual Hour maintenance, 10 15 hour maintenance, Every 20 and 100 hours

Page 10

Maintenance (continued)

10 - hour maintenance

(more frequently in dusty conditions)

1.Remove the air filter element, and wash the element in clean, neutral solvent or warm soapy water. Rinse the ele- ment thoroughly, and then squeeze dry before reassembly.

CAUTION!

1HYHURSHUDWHWKHXQLWLIWKHDLU¿OWHU assembly is damaged or missing or LIWKHDLU¿OWHUHOHPHQWLVVRDNHGZLWK water!

$LU¿OWHUHOHPHQW

$LU¿OWHUFRYHU

&OHDQDLU¿OWHU

10 - 15 hour maintenance

Remove and clean the spark plug. Adjust the spark plug electrode gap to 0.024 - 0.028 inch (0.6 - 0.7 mm). If the spark plug must be replaced, use only the spark plug recommended on the Specifica- tions section or an equivalent resistor type spark plug of the correct heat range.

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts. .

0.6–0.7 mm

(0.024–0.028 inch )

Remove the spark plug and adjust the gap at the electrode

Every 20 and 100 hours

Gearcase lubrication

CAUTION!

ŶOver-lubricating may cause the gearcase to run slower than normal, and may also cause leakage from excess grease.

ŶDo not remove the conrods from the cutters. Conrod bearings can be lost or damaged if disturbed.

Every 20 hours

Top off gearcase grease level by using a lever-type grease gun to force 1–2 strokes of high quality lithium-based grease through the gearcase grease fitting.

Every 100 hours

(or before long-term storage)

Remove the gearcase cover, and use sol- vent and a soft brush to remove all old grease from the gearcase. To refill, hand- pack the gearcase with approximately 40–50 grams of high quality lithium-based grease (50–70% of capacity). DO NOT OVERFILL!

*UHDVH¿WWLQJ

 

BOTTOM

 

VIEW

DO NOTE REMOVE

 

CONRODS

 

BOTTOM VIEW

 

Gearcase cover

Hex screws

 

Gearcase lubrication

 

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HT231 Hedge Trimmer Safety and operation labels ContentsIntroduction Work Safely SafetySafety devices and labels Stay AlertIt free of loose vegetation, mud, etc Operating the Hedge TrimmerRPM without a load. Doing so could Wipe off any fuel that may have To the unit SpilledProduct Description Do not alter this machine or any of its componentsExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireStarting the Engine Starting the EngineBefore starting the engine Make sure you have a secureStopping the engine Adjusting engine idleOperation Daily maintenance MaintenanceGeneral maintenance Spark Plug10 15 hour maintenance Hour maintenanceEvery 20 and 100 hours Every 50 hours of operation more Throttle free play adjustmentCutter blade adjustment Often in dusty or dirty conditionsFor carbon buildup Long Term StorageRemove the spark arrester screen Sult your servicing dealerWhat To Check Troubleshooting GuideEngine does not Start Possible CauseOperate at slower rate LOW PowerIs the engine overheating? Engine is knockingAdditional Problems Emission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan Cortasetos HT231 ¡ADVERTENCIADeclaraciones De Seguridad IntroducciónContenido Etiquetas informativas sobre seguridad y funcionamientoMantengase Alerta SeguridadTrabaje con cuidado Etiquetas de seguridadPrecauciones de operaciones Seguridad continuaciónDe hierba, barro, etc Descripción del Producto VshflàfdflrqhvPrecaución Mezcla de CombustibleLlenando el Tanque de Combustible AdvertenciaAntes de usarla Arranque del motorArranque del motor Ajuste de la Marcha Mínima Arranque del motor continuaciónParada del Motor OperaciónSilenciador MantenimientoMantenimiento generale BujíaMantenimiento cada 10 horas Mantenimiento continuaciónCada 20 y 100 horas Más frecuente en condiciones polvorientas o adversas Mantenimiento cada 50 horasCuchillas Retire y reemplace el elemento del filtroMantenimiento cada 139 horas Almacenamiento de Largo PlazoQué revisar Guia DiagnosticoEL Motor no Arranca Posible causa¿Se sobrecalienta el motor? Guia Diagnostico continuaciónBaja Potencia Depósitos de carbonilla en el pistón o el silenciadorOtros Problemas Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaRemarques SP18 SP19 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE À Lame HT231 AvertissementÉtiquettes au fonctionnement et à la sécurité Table des MatièresMises en garde Mise EN GardeSécurité au travail SécuritéÉtiquettes de sécurité Maintien prévu recommandé Ment serré avant toute utilisation Sécurité suiteNomenclature Caractéristiques techniquesExemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieAvant démarrage Démarrage du moteurDémarrage du moteur Réglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur UtilisationEntretien Toutes les 10 à 15 heures d’utilisation Entretien suiteEntretien aux 10 heures Toutes les 20 et 100 heures d’utilisationLe jeu du levier d’accélérateur Remplacement du filtre à carburantEntretien aux 50 heures Réglage de la lameRemisage à long terme Entretien aux 139 heuresLE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cogneAutres Problèmes Couverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantieFR17 FR18 FR19

89309 specifications

Shindaiwa 89309 is a high-performance trimmer head designed for both professional landscapers and avid gardeners who demand reliability, efficiency, and ease of use. This product stands out in a crowded market due to its innovative engineering and robust construction, making it an essential tool for those who take lawn care seriously.

One of the main features of the Shindaiwa 89309 is its durable design. Constructed from high-quality materials, it is built to withstand the rigors of everyday use while maintaining optimal performance. This means users can tackle tough tasks without the fear of wear and tear, ensuring longevity and durability.

The trimmer head integrates advanced technologies to improve efficiency and ease of operation. One of its most notable technologies is the easy-loading spool system, which allows users to quickly and effortlessly reload the line. This feature significantly reduces downtime, enabling users to get back to their work without hassle.

Additionally, the Shindaiwa 89309 is designed with a dual-line cutting system, which enhances its cutting performance. This system provides a wider cutting path, allowing users to cover more ground in less time. The trimmer head delivers clean and precise cuts, ultimately resulting in a neater finish for lawns and gardens.

Another key characteristic of the Shindaiwa 89309 is its compatibility. The trimmer head works seamlessly with various Shindaiwa machines, allowing for versatility and ease of integration into existing tool collections. This adaptability makes it a practical choice for professionals with multiple pieces of equipment.

Moreover, the Shindaiwa 89309 features an efficient balance that reduces user fatigue. The lightweight design combined with a well-thought-out weight distribution allows for extended periods of use without straining the operator, which is crucial in a demanding work environment.

In summary, the Shindaiwa 89309 trimmer head embodies the perfect blend of durability, efficiency, and user-friendly features. Its advanced technologies, including the easy-loading spool and dual-line cutting system, make it an invaluable tool for achieving pristine landscaping results. Whether for professional use or personal projects, the Shindaiwa 89309 stands out as a reliable choice for trimmers and gardeners alike.
Top Page Image Contents