Shindaiwa 89309 manual Mixing fuel, Filling the fuel tank, Examples of 501 mixing quantities

Page 6

Mixing fuel

CAUTION

Never use any type of gasoline contain- ing more than 10% alcohol by volume! Some types of gasoline contain alcohol as an oxygenate. Oxygenated gaso- line may cause increased operating temperatures. Under certain condi- tions, alcohol-based gasoline may also reduce the lubricating qualities of some 2-cycle mixing oils.

Generic oils and some outboard oils should never be used in your Shindaiwa engine.

CAUTION

This engine is designed to operate on a 50:1 mixture consisting of unleaded gasoline and ISO-L-EGD or JASO FD class 2-cycle mixing oil only. Use of non-approved mixing oils can lead to excessive carbon deposits.

ŶUse only fresh, clean unleaded gasoline with a pump octane of 87 or higher.

ŶMix all fuel with a 2-cycle air-cooled mixing oil that meets or exceeds ISO-L- EGD and/or JASO FD classified oils at 50:1 gasoline/oil ratio.

CAUTION!

Mix and pour fuel outdoors where there DUHQRVSDUNVDQGÀDPHV

Examples of 50:1 mixing quantities

U.S.

METRIC

Gasoline

2-cycle

Gasoline

2-cycle

mixing oil

mixing oil

US Gallons

Fl.oz.

Liter

cc.

1

2.6

4

80

2

5.2

8

160

5

13

20

400

10

25.6

30

600

20

51.2

50

1000

50

128

100

2000

IMPORTANT!

Mix only enough fuel for your immediate needs! If fuel must be stored longer than 30

days and oil with fuel stabilizer is not used, it should first be treated with a fuel stabilizer such as STA-BIL™.

Oil is a registered JASO FD classi- fied oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emis- sions engines. Shindaiwa One also includes a fuel stabilizer.

Filling the fuel tank

WARNING!

Minimize the Risk of Fire

ŶNEVERVPRNHRUOLJKW¿UHVQHDUWKH engine.

ŶALWAYS stop the engine and allow it to cool before refueling.

ŶALWAYS Wipe all spilled fuel and move at least 3 meters (10 feet) from the fueling point and source before starting.

ŶNEVERSODFHÀDPPDEOHPDWHULDO FORVHWRWKHHQJLQHPXIÀHU

ŶNEVER operate the engine with-

RXWWKHPXIÀHUDQGVSDUNDUUHVWHU screen in place and in good work- ing condition.

ŶFUEL IS HIGHLY FLAMMABLE.

ŶALWAYS store gasoline in a con-

WDLQHUDSSURYHGIRUÀDPPDEOH

liquids.

ŶALWAYS inspect the unit for fuel leaks before each use. During each

UH¿OOFKHFNWKDWQRIXHOOHDNVIURP around the fuel cap and/or fuel tank. If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit.

ŶALWAYS move the unit at least 3 meters (10 feet) away from a fuel

VWRUDJHDUHDRURWKHUUHDGLO\ÀDP- mable materials before starting the engine.

1.Place the unit on a flat, level surface.

2.Clear any dirt or other debris from around the fuel filler cap.

CAUTION!

Slowly remove the fuel cap only after stopping the engine

3.Remove the fuel cap, and fill the tank with clean, fresh fuel.

4.Reinstall the fuel filler cap and tighten firmly.

5.Wipe away any spilled fuel before start- ing engine.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HT231 Hedge Trimmer Contents Safety and operation labelsIntroduction Work Safely SafetySafety devices and labels Stay AlertIt free of loose vegetation, mud, etc Operating the Hedge TrimmerRPM without a load. Doing so could Wipe off any fuel that may have To the unit SpilledProduct Description Do not alter this machine or any of its componentsExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireStarting the Engine Starting the EngineBefore starting the engine Make sure you have a secureAdjusting engine idle Stopping the engineOperation Daily maintenance MaintenanceGeneral maintenance Spark PlugHour maintenance 10 15 hour maintenanceEvery 20 and 100 hours Every 50 hours of operation more Throttle free play adjustmentCutter blade adjustment Often in dusty or dirty conditionsFor carbon buildup Long Term StorageRemove the spark arrester screen Sult your servicing dealerWhat To Check Troubleshooting GuideEngine does not Start Possible CauseOperate at slower rate LOW PowerIs the engine overheating? Engine is knockingAdditional Problems Emission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan Cortasetos HT231 ¡ADVERTENCIADeclaraciones De Seguridad IntroducciónContenido Etiquetas informativas sobre seguridad y funcionamientoMantengase Alerta SeguridadTrabaje con cuidado Etiquetas de seguridadSeguridad continuación Precauciones de operacionesDe hierba, barro, etc Descripción del Producto VshflàfdflrqhvPrecaución Mezcla de CombustibleLlenando el Tanque de Combustible AdvertenciaArranque del motor Antes de usarlaArranque del motor Ajuste de la Marcha Mínima Arranque del motor continuaciónParada del Motor OperaciónSilenciador MantenimientoMantenimiento generale BujíaMantenimiento continuación Mantenimiento cada 10 horasCada 20 y 100 horas Más frecuente en condiciones polvorientas o adversas Mantenimiento cada 50 horasCuchillas Retire y reemplace el elemento del filtroMantenimiento cada 139 horas Almacenamiento de Largo PlazoQué revisar Guia DiagnosticoEL Motor no Arranca Posible causa¿Se sobrecalienta el motor? Guia Diagnostico continuaciónBaja Potencia Depósitos de carbonilla en el pistón o el silenciadorOtros Problemas Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaRemarques SP18 SP19 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE À Lame HT231 AvertissementÉtiquettes au fonctionnement et à la sécurité Table des MatièresMises en garde Mise EN GardeSécurité Sécurité au travailÉtiquettes de sécurité Maintien prévu recommandé Ment serré avant toute utilisation Sécurité suiteNomenclature Caractéristiques techniquesExemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieDémarrage du moteur Avant démarrageDémarrage du moteur Réglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur UtilisationEntretien Toutes les 10 à 15 heures d’utilisation Entretien suiteEntretien aux 10 heures Toutes les 20 et 100 heures d’utilisationLe jeu du levier d’accélérateur Remplacement du filtre à carburantEntretien aux 50 heures Réglage de la lameRemisage à long terme Entretien aux 139 heuresLE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cogneAutres Problèmes Couverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantieFR17 FR18 FR19

89309 specifications

Shindaiwa 89309 is a high-performance trimmer head designed for both professional landscapers and avid gardeners who demand reliability, efficiency, and ease of use. This product stands out in a crowded market due to its innovative engineering and robust construction, making it an essential tool for those who take lawn care seriously.

One of the main features of the Shindaiwa 89309 is its durable design. Constructed from high-quality materials, it is built to withstand the rigors of everyday use while maintaining optimal performance. This means users can tackle tough tasks without the fear of wear and tear, ensuring longevity and durability.

The trimmer head integrates advanced technologies to improve efficiency and ease of operation. One of its most notable technologies is the easy-loading spool system, which allows users to quickly and effortlessly reload the line. This feature significantly reduces downtime, enabling users to get back to their work without hassle.

Additionally, the Shindaiwa 89309 is designed with a dual-line cutting system, which enhances its cutting performance. This system provides a wider cutting path, allowing users to cover more ground in less time. The trimmer head delivers clean and precise cuts, ultimately resulting in a neater finish for lawns and gardens.

Another key characteristic of the Shindaiwa 89309 is its compatibility. The trimmer head works seamlessly with various Shindaiwa machines, allowing for versatility and ease of integration into existing tool collections. This adaptability makes it a practical choice for professionals with multiple pieces of equipment.

Moreover, the Shindaiwa 89309 features an efficient balance that reduces user fatigue. The lightweight design combined with a well-thought-out weight distribution allows for extended periods of use without straining the operator, which is crucial in a demanding work environment.

In summary, the Shindaiwa 89309 trimmer head embodies the perfect blend of durability, efficiency, and user-friendly features. Its advanced technologies, including the easy-loading spool and dual-line cutting system, make it an invaluable tool for achieving pristine landscaping results. Whether for professional use or personal projects, the Shindaiwa 89309 stands out as a reliable choice for trimmers and gardeners alike.
Top Page Image Contents