Shindaiwa 89309 manual Stopping the engine, Adjusting engine idle, Operation

Page 8

Starting the engine (continued)

When the motor starts...

1. Open the choke by moving the choke

3. When the engine starts, clear excess

If the engine does not start

lever backward (toward the fuel tank).

fuel from the combustion chamber by

Ŷ Repeat the appropriate starting proce-

2. If the engine does not continue to run,

accelerating the engine several times

with the throttle lever.

dure for a cold or warm engine.

repeat the appropriate cranking proce-

Ŷ If the engine still fails to start, use the

 

dures for a cold or warm engine.

4. Operating the throttle will automatically

 

disengage the fast idle setting.

procedures for “Starting a flooded

 

engine.”.

 

 

6WDUWHGDÁRRGHGHQJLQH

WARNING!

Burn danger from hot engine! Allow engine to cool before removing cylinder cover.

1.Disconnect the spark plug lead, and then use the spark plug wrench to loosen and remove the spark plug.

2.If the spark plug is fouled or is soaked with fuel, clean or replace the plug as necessary. For spark plug specifications see the “10 - 15 Hour Maintenance” section.

3.With the spark plug removed, crank the engine several times to clear excess fuel from the combustion chamber.

4.Replace the spark plug and tighten it firmly with the spark plug wrench. If a torque wrench is available, torque the spark plug to the values in the “Specifi- cations” section.

5.Repeat the starting procedures for a warm engine.

CAUTION!

Incorrect spark plug installation can damage the engine!

Spark plug

wire

Spark plug

6WDUWLQJDÀRRGHGHQJLQH

If the engine still fails to start or fire, refer to the troubleshooting chart at the end of this manual.

Stopping the engine

1.Cool the engine by allowing it to idle for 2–3 minutes.

2. Move the ignition switch to the “O” or

Ignition OFF (O)

STOP position.

 

Adjusting engine idle

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

WARNING!

The cutters must NEVER engage at engine idle speeds! If the idle speed cannot be adjusted by the procedure, described here, contact your authorized Shindaiwa servicing dealer.

Idle Speed Adjustment

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

3.If a tachometer is available, the engine idle speed should be final adjusted to the values in the Specification section..

NOTE

Carburetor fuel mixture adjustments are preset at factory and cannot be serviced LQWKH¿HOG

Idle adjustment

screw

Operation

ŶSqueezing the throttle increases engine speed, causing the clutch to engage and operate the cutters.

ŶReleasing the throttle decreases engine speed, causing the cutters to slow, and then stop altogether as the clutch disengages.

ŶUse a sweeping motion when cutting, and vary throttle settings often.

ŶAvoid cutting material larger than 1.27 cm in diameter.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents HT231 Hedge Trimmer Introduction ContentsSafety and operation labels Safety Safety devices and labelsWork Safely Stay AlertOperating the Hedge Trimmer RPM without a load. Doing so couldIt free of loose vegetation, mud, etc Wipe off any fuel that may have To the unit SpilledProduct Description Do not alter this machine or any of its componentsMixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireStarting the Engine Before starting the engineStarting the Engine Make sure you have a secureOperation Adjusting engine idleStopping the engine Maintenance General maintenanceDaily maintenance Spark PlugEvery 20 and 100 hours Hour maintenance10 15 hour maintenance Throttle free play adjustment Cutter blade adjustmentEvery 50 hours of operation more Often in dusty or dirty conditionsLong Term Storage Remove the spark arrester screenFor carbon buildup Sult your servicing dealerTroubleshooting Guide Engine does not StartWhat To Check Possible CauseLOW Power Is the engine overheating?Operate at slower rate Engine is knockingAdditional Problems Emission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan Cortasetos HT231 ¡ADVERTENCIAIntroducción ContenidoDeclaraciones De Seguridad Etiquetas informativas sobre seguridad y funcionamientoSeguridad Trabaje con cuidadoMantengase Alerta Etiquetas de seguridadDe hierba, barro, etc Seguridad continuaciónPrecauciones de operaciones Descripción del Producto VshflàfdflrqhvMezcla de Combustible Llenando el Tanque de CombustiblePrecaución AdvertenciaArranque del motor Arranque del motorAntes de usarla Arranque del motor continuación Parada del MotorAjuste de la Marcha Mínima OperaciónMantenimiento Mantenimiento generaleSilenciador BujíaCada 20 y 100 horas Mantenimiento continuaciónMantenimiento cada 10 horas Mantenimiento cada 50 horas CuchillasMás frecuente en condiciones polvorientas o adversas Retire y reemplace el elemento del filtroMantenimiento cada 139 horas Almacenamiento de Largo PlazoGuia Diagnostico EL Motor no ArrancaQué revisar Posible causaGuia Diagnostico continuación Baja Potencia¿Se sobrecalienta el motor? Depósitos de carbonilla en el pistón o el silenciadorOtros Problemas Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaRemarques SP18 SP19 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE À Lame HT231 AvertissementTable des Matières Mises en gardeÉtiquettes au fonctionnement et à la sécurité Mise EN GardeÉtiquettes de sécurité SécuritéSécurité au travail Maintien prévu recommandé Ment serré avant toute utilisation Sécurité suiteNomenclature Caractéristiques techniquesMélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Démarrage du moteurAvant démarrage Démarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur UtilisationEntretien Entretien suite Entretien aux 10 heuresToutes les 10 à 15 heures d’utilisation Toutes les 20 et 100 heures d’utilisationRemplacement du filtre à carburant Entretien aux 50 heuresLe jeu du levier d’accélérateur Réglage de la lameRemisage à long terme Entretien aux 139 heuresSolution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes La présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantieFR17 FR18 FR19

89309 specifications

Shindaiwa 89309 is a high-performance trimmer head designed for both professional landscapers and avid gardeners who demand reliability, efficiency, and ease of use. This product stands out in a crowded market due to its innovative engineering and robust construction, making it an essential tool for those who take lawn care seriously.

One of the main features of the Shindaiwa 89309 is its durable design. Constructed from high-quality materials, it is built to withstand the rigors of everyday use while maintaining optimal performance. This means users can tackle tough tasks without the fear of wear and tear, ensuring longevity and durability.

The trimmer head integrates advanced technologies to improve efficiency and ease of operation. One of its most notable technologies is the easy-loading spool system, which allows users to quickly and effortlessly reload the line. This feature significantly reduces downtime, enabling users to get back to their work without hassle.

Additionally, the Shindaiwa 89309 is designed with a dual-line cutting system, which enhances its cutting performance. This system provides a wider cutting path, allowing users to cover more ground in less time. The trimmer head delivers clean and precise cuts, ultimately resulting in a neater finish for lawns and gardens.

Another key characteristic of the Shindaiwa 89309 is its compatibility. The trimmer head works seamlessly with various Shindaiwa machines, allowing for versatility and ease of integration into existing tool collections. This adaptability makes it a practical choice for professionals with multiple pieces of equipment.

Moreover, the Shindaiwa 89309 features an efficient balance that reduces user fatigue. The lightweight design combined with a well-thought-out weight distribution allows for extended periods of use without straining the operator, which is crucial in a demanding work environment.

In summary, the Shindaiwa 89309 trimmer head embodies the perfect blend of durability, efficiency, and user-friendly features. Its advanced technologies, including the easy-loading spool and dual-line cutting system, make it an invaluable tool for achieving pristine landscaping results. Whether for professional use or personal projects, the Shindaiwa 89309 stands out as a reliable choice for trimmers and gardeners alike.
Top Page Image Contents