2 TM-2430 Series Error Codes | A&D TM-2430-13 instruction

3-1-2 TM-2430 Series Error Codes

ERROR CODE	POSSIBLE CAUSE			CORRECTION
E00	Clock parameters have not been			Enter clock parameters.
	set.
E03	An error code is displayed			Exhaust the air from the cuff completely.
	without cuff inflation.
E04	Measurement is stopped due to a			Replace with new batteries. Auto mode
	low battery.			is quit. Restart the Auto mode if you use
				it.
E05	Inflation pressure does not reach			Wrap the cuff and connect to the
	the target pressure.			monitor. If the error persists, there may
				be an air leak and repair is necessary.
E06	Pressurization greater		than 320	Do not move and try to relax during the
	mmHg.			measurement. If you can not clear the
				error, repair is necessary.

E07	Controlled stop using STOP key			Do not press the STOP key when
				unnecessary.

E08, E10	Pulse can not be detected.			Do not move and try to relax during the
				measurement.

E20	Pulse less than 35 beats or more			Measure the blood pressure by other
	than 200 beats per minute.			methods.

E21	Diastolic greater than 160 mmHg			Measure the blood pressure by other
	or less than 40 mmHg.			methods.

E22	Systolic greater than 280 mmHg			Measure the blood pressure by other
	or less than 60 mmHg.			methods.

E23	DSD greater than 150 mmHg or			Measure the blood pressure by other
	less than 10 mmHg.			methods.
	(DSD = difference between
	systolic blood pressure and
	diastolic blood pressure)

E30, E31	Air leaks in the cuff assembly.			Repair is necessary.

E32	Clock error			If the error persists, repair is necessary.

E50	Pressure offset error			Repair is necessary.

E52	Memory error			Repair is necessary.

E53	Defective battery contact			Replace batteries correctly. If the error
				persists, repair is necessary.

E55, E56, E57	Exhaust error			Relax and do not move during the
				measurement. If this error occurs
				frequently, repair is necessary.

E60	Interval setting error			Enter the interval parameters correctly.

E70, 71, 72, 73	RS-232C error			Re-connect the communication cable. If
				the error persists, repair is necessary.

E74	Voltage	decreases	during	Replace batteries with new ones and
	communication.			restart communication.

E75	Protocol error due to external			Re-connect the communication cable. If
	equipment			the error persists, repair is necessary.

50

Image 51

A&D TM-2430-13 instruction manual 2 TM-2430 Series Error Codes

Contents

TM-2430-13 Contents Troubleshooting About the Data Analysis Software Introduction Monitoring Device Review Symbols System Requirements Installing the SoftwareSafety Software Package Components Communication Between the Monitor and the Software Connecting the TM-2420/TM-2421 to the computerGetting Started Communication Between the Monitor and the Software Connecting the TM-2430 series to the computer Connecting the UA-767PC to the computer Main Screen Description Toolbar Analysis Intervals BP Mode Method Setting Description Menu Description File Menu Delete Save As Convert File MergeSelect the Merge the BP data files sub-menu Saving a File PrintClick Open Exit View Menu Summary Data display Errors for Summary Data Tab DefinitionBP Blood Status See 3-1 Measurement Errors Entering Comments Excluding/Including BP Measurements Mean Arterial Blood Pressure MAP Trend Linking to Trends ScreenSystolic/Diastolic Blood Pressure BP Trend Pulse Pulse Trend Scroll bar/Linking Delimitation, Scroll Bar and Linking Partial AnalysisSleep Blood Pressure Trend BP Limits Viewing the Trends Scaling the ScreenTrend Display Positioning Trends Creating a New/Edit Trends Template Trend Page Setup dialog box Blood Pressure Trend Setup dialog box Correlation Plots display Pulse Systolic Blood PressureDiastolic Blood Pressure MAP, Mean Blood Arterial Pressure Circadian Rhythm display HIB analysis display HIB Analysis Physician List Field DescriptionIntervals and Conditions Data retrieval. See 2-7-1 Retrieving Data from the Monitor Select the Patient Information sub-menu Recorder Menu Retrieving Data from the Monitor Select the Recorder menu Select the Retrieve data sub-menuClick the Retrieve Data button Select the Recorder menu Clearing The Monitor’s Memory Monitoring session is performed at the same interval for TM-2420/TM-2421 Recorder Setup dialog box Description of each mode is as follows 3-2 TM-2430 Series Setup Period Start Interval Monitor programming example Example Programming the Monitor for Three 3 Periods OFF Example Programming the Monitor for Four 4 Periods Blood Pressure Measurement Available only with the UA-767PC 3-4 UA-767PC Setup Report dialog box Report Menu Creating a New Report Template Report setup dialog box Printing an Existing Report Template Saving a Default Report Template for PrintingEditing an Existing Report Template Deleting an Existing Report Template Options Menu Trend Display See 2-6-3-3 Trend Display Positioning Trends Adding a New Physician to the ListEditing an Existing Physician in the List Deleting an Existing Physician in the List Default Blood Pressure Settings dialog box On-line Help Serial PortRecorder Type Well as programmed intervals Measurement Errors1 TM-2420/TM-2421 Error Codes Be erased Be taped to the arm with the supplied 2 TM-2430 Series Error Codes Communications Error dialog box Communication Errors Reports Are Not Printing With the Desired BP Mode Missing FilesSummary Data / Sleep Tab Data can not be Seen Printout Examples Summary data Full and partial Text data Summary data Awake and sleep Text data Blood pressure data Text data Trend graph Blood pressure and double product Graphical data Page Page Mini report Mini report Terms Related to Statistics Terms Related to Blood Pressure Mesor Terms Related to Biological Rhythm 95% confidence interval is expressed Terms Related to the Risk Management of High Blood Pressure Memo Memo Memo