Air supply and flue gas discharge | A.O. Smith 28 30 50 60 specification

is

3.9Air supply and flue gas discharge

Air supply and flue gas discharge

4. Fit the gas supply pipe to the gas control.

Warning

Check for leaks after fitting.

Warning

The installation should be carried out by an authorised installer, in compliance with the general and local regulations imposed by gas, water supply and power supply companies and the fire service. Refer also to paragraph ’1.3 Regulations’.

Depending on the approved installation types, there are several alternatives for connecting the air supply and flue gas discharge. The BFC appliances are approved for installation types C13, C33, C43, C53 and C63.

The most common installation types are:

•C13: Concentric wall flue terminal and

•C33: Concentric roof flue terminal.

This manual describes these installation types. If an explanation of other types of installation is required, please contact A.O. Smith.

cNote

A.O. Smith prescribes the use of a roof or wall-mounted terminal, exclusively of a type approved for the appliance. See paragraph

’3.9.1 Concentric wall flue terminal’ and ’3.9.2 Concentric roof flue terminal’. Use of an incorrect roof or wall-mounted terminal can cause the installation to malfunction.

nRemark

Make sure that the chimney discharges into an area where this is permitted for this category of appliance.

Table 3.7 shows the maximum length of the chimney configurations. The following requirements must also be fulfilled:

•the maximum chimney length is 15 metres.

•The maximum permitted number of 45° or 90° bends is four.

Table 3.7 Chimney configurations for concentric wall and roof termination.

Dimension	BFC 28	BFC 30	BFC 50	BFC 60
(1)

A	0-15 m	0-15 m	0-15 m	0-15 m

B	0-15 m	0-15 m	0-15 m	0-15 m

a + B	max. 15 m	max. 15 m	max. 15 m	max. 15 m

1.See ’Figure 3.4 Wall flue terminal’ and ’Figure 3.5 Roof flue terminal’.

cNote

If you make use of horizontal piping, then this must slope towards the appliance with a minimum of 5 mm per metre running length!

Release R.1.3 UK

27

Image 27

A.O. Smith 28 30 50 60 service manual Air supply and flue gas discharge, Dimension BFC

Contents

Release R.1.3 UK Your installer More information CopyrightTrademarks LiabilityPage Gis Table of contents Starting up and shutting down Filling and drainingControl panel Status of the appliance Maintenance Service programTroubleshooting Maintenance frequency Index Appendices Introduction What to do if you smell gas RegulationsAbout the appliance Introduction Target groups Maintenance Forms of notationSymbol Target group Remark Chapter Target groups Description Overview of thisDocument Overview of this document Gis Functioning of the appliance Introduction Functional description of the applianceIntroduction Water temperature protection Gas control Pressure switch Ionisation rodAppliance’s heating cycle Protection for the appliance 3 Fan Water temperature protectionPressure switch Gas control Ionisation rod Safety of the instal- lationUnvented installation Vented installation Introduction Packaging Environmental conditions Installation Working clearances Humidity and ambient temperatureMaximum floor loading Water composition Working clearances Environmental conditions Plan and elevation of the appliance Technical specifications Unit BFC DimensionsTechnical specifications Dime Description BFC Nsion VAC G30-30 mbar butane Installation diagramGas data General Unvented Installation Condensation drainage Water connections, Unvented Cold water sideHot water side Circulation pipe See din Figure Water connections, VentedGas connection See paragraph ’3.6.4 Condensation drainage’ Dimension BFC Air supply and flue gas dischargeAir supply and flue gas discharge Concentric wall flue terminal Specification Description Concentric roof flue terminal Concentric roof flue terminal specifications Electrical connection PreparationPreparation Mains voltage Electrical connection Mains voltage Program-controlled pump Extra on mode switch Tank onIsolating Transformer Continuous pump Appliance Connecting extra error signal Alarm OUTChecking the supply Pressure and burner Checking the supply pressure and burner pressure Main menu Conversion to a different gas category Conversion to a different gas category Remove the burner as complete assembly Check the burner and supply pressure see paragraph 13 Conversion of gas control Installation Filling the appliance Filling the appliance Filling unvented installationsFilling vented installations Filling and draining Filling and draining Installation diagrams F d c Draining the appliance Draining unvented installationsDraining vented installations Draining the appliance Gis Introduction Operating Control panel Control panel Explanation of the icons ON/OFF switch of ThermoControlNavigation buttons PC connection Operating modes Error conditions Service condition Status of the applianceIntroduction Operating modes Status of the appliance Error conditions Service condition Service condition Gis Shutting down Open the gas valve see ’ .1 Installation diagrams’Starting up and shutting down Introduction Starting up Starting up and shutting down Shut the appliance down for a brief period OFF modeDisconnect the appliance from the mains Shut the appliance down for a longer period Appliance’s heating cycle Appliance’s heating cycle 12 Ignition Notational convention for menu-related instructions Main menu Switching into on mode Setting the water temperature Setting the water temperature via Setpoint MenuSetting water temperature during on mode Week programme Introduction Starting up and shutting down the week programChanging the appliance’s standard week program Remark Setting the switch-on time Setting switch-off timeExample Week programme Setting the water temperatureSetting program-controlled pump Adding times to a week program 20 Period added Deleting times from a week program 23 week program options Programming an extra period Extra period Settings Setting menu languageSettings Displaying appliance specifications Remark Setting day and time 46 Main menu Gis Service program Setting the hysteresisDisplaying the error history Displaying the appliance history Setting the pump on/offSetting the service interval Service program Setting the display contrast Setting the display contrastSetting the backlight time Setting the display scroll speed Service program Troubleshooting General errorsDisplayed errors Symptom Cause Solution Remark Gas smell Gas leak Troubleshooting table for general errors Symptom Cause Solution Remark Display is off See appendix ’A.2 Electrical diagram BFC’Water leakage Water Troubleshooting table for displayed errorsSymptom Cause Solution Remark Explosive ignition Insufficient or no hot S05 blocking error S02 blocking errorS03 blocking error S04 blocking error S13 blocking error S14 blocking errorS15 blocking error F02 lock out error Phase-sensitive. See ’3.10 Electrical connection’ Appliance specifications’ How to bleed air from the gas line, and measure the supply ’3.9 Air supply and flue gas discharge’ F06 lock out errorF07 lock out error F08 lock out error F10 lock out error Error F09 remains active in the event that the water Release R.1.3 UK Release R.1.3 UK E04 blocking error C04 blocking errorE01 blocking error E03 blocking error Determining service interval Maintenance frequency Maintenance frequency Remark Preparation for maintenance Maintenance Starting up Maintenance Water-side mainte- nance Introduction Descaling and cleaning the tankCleaning condensation water discharge Cleaning the burner Remark Finalising mainte- nance Cleaning the orificeCleaning heat exchanger 12.4.3 Warranty Certificate Warranty Certificate Week program card Appendices Appendices Electrical diagram Week program card Release R.1.3 UK Index IX Index IX Index 0306