A.O. Smith 28 30 50 60 9is

Service program

66 Instruction Manual BFC

9is

Figure 9.3 shows an example of ‘Blocking errors’. In this case, the text

HISTORIE OF ERRORS is followed by (B).

Figure 9.4 shows an example of the ‘Lock out errors’. In this case, the text

HISTORIE OF ERRORS is followed by (L).

nRemark

For an overview of all errors and the possible causes, please refer to chapter

’10 Troubleshooting’.

9.4 Displaying the

appliance history

The appliance history sub-menu is used to display the burning hours, the

number of ignitions, the number of flame errors, and the number of ignition

errors.

Bring up the menu for displaying the appliance history via:

•S: APPLIANCE HISTORY

Figure9.5 shows an example.

9.5 Display the selected

appliance

Bring up the menu for displaying the appliance selection via:

•S: SELECT APPLIANCE

The appliance selection has been correctly preset in the factory.

Figure9.6 shows the relevant display.

9.6 Setting the pump

on/off

If a program-controlled pump is installed (Installation, see paragraph 3.10.6)

then this can be turned ON or OFF via:

•S: PUMP RELAY

The standard setting for the pump relay is OFF.

Figure9.7 shows the related display.

If the mode WEEK PROGRAM or EXTRA PERIOD is active, then the setting for

mode WEEK PROGRAM or EXTRA PERIOD has priority over the ON/OFF

selection for the pump relay in the service menu.

Example

One of the week program periods is currently active. The pump relay setting is

OFF within this period. If the pump relay is set ON in the service menu, the pump

will nonetheless remain OFF. The pump will only switch ON once the week

program period has ended.

9.7 Setting the service

interval

To aid servicing, the ThermoControl has a service interval which defines the

frequency of maintenance by the service and maintenance engineer based on

the number of burning hours. Refer also to paragraph 11.2.

HISTORIE OF ERRORS(B)

S04 SENSOR ERROR

F06 IONIZATION

È CO2 50 HZ ERROR

Figure 9.3 Blocking errors

HISTORIE OF ERRORS(L)

F02: FAN

F07: FLAME ERROR

È ...

Figure 9.4 Lock out errors

APPLIANCE HISTORY

BURNINGHOURS 000410

^IGNITIONS 001000

ÈFLAME ERRORS 000021

IGNIT ERROR 000013

Figure 9.5 service program

SELECT APPLIANCE

»ADM 40 - 135

^ ADMR 40 - 135

È BFC 28

BFC 30

BFC 50

BFC 60

BFC 80

BFC 100

Figure 9.6 Select appliance

PUMP RELAY

»ON

OFF

Figure 9.7 Pump relay

Contents

Main Page Release R.1.3 UK 3 Copyright Trademarks Liability More information Page Release R.1.3 UK 5 Table of contents 1 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - 9 2 Functioning of the appliance- - - - - - - - - - - - - - - - - - 13 3 Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - 17 4 Filling and draining - - - - - - - - - - - - - - - - - - - - - - - 39 5 The control panel- - - - - - - - - - - - - - - - - - - - - - - - 43 6 Status of the appliance - - - - - - - - - - - - - - - - - - - - - 45 7 Starting up and shutting down - - - - - - - - - - - - - - - - - 49 8 Main menu - - - - - - - - - - - - - - - - - - - - - - - - - - - 53 Release R.1.3 UK 7 9 Service program - - - - - - - - - - - - - - - - - - - - - - - - 65 10 Troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - 69 11 Maintenance frequency - - - - - - - - - - - - - - - - - - - - 83 12 Maintenance - - - - - - - - - - - - - - - - - - - - - - - - - - 85 Page Release R.1.3 UK 9 1 Introduction 1.1 About the appliance 1.2 What to do if you smell gas Warning 1.3 Regulations 1gis g i s Page Page Release R.1.3 UK 13 2 Functioning of the appliance 2.1 Introduction 2.2 Functional description of the 14 Instruction Manual BFC 2gis 2.3 The appliances heating cycle 2.4 Protection for the Release R.1.3 UK 15 2.4.1 Water temperature protection 2.4.2 Gas control 2.4.3 Fan 2.4.4 Pressure switch 2gis 2.4.5 Ionisation rod 2.5 Safety of the instal- lation 2.5.1 Unvented installation 2.5.2 Vented installation 3 Installation Page Page Page Release R.1.3 UK 21 Table 3.4 Dimensions Page Release R.1.3 UK 23 Table 3.6 Gas data 3.5 Installation diagram Gas category data Page Page Page Page 28 Instruction Manual BFC 3.9.1 Concentric wall flue terminal Table 3.8 Concentric wall flue terminal specifications Release R.1.3 UK 29 3.9.2 Concentric roof flue terminal Table 3.9 Concentric roof flue terminal specifications 30 Instruction Manual BFC 3.10 Electrical connection Warning 3.10.1 Introduction 3.10.2 Preparation Table 3.10 Electrical connection block Release R.1.3 UK 31 3.10.3 Mains voltage 32 Instruction Manual BFC 3.10.4 Isolating Transformer 3.10.5 Continuous pump 3.10.6 program-controlled pump 3.10.7 Extra ON mode switch (Tank ON) Release R.1.3 UK 33 3.10.8 Connecting extra error signal (Alarm OUT) 3.11 Checking the supply pressure and burner pressure Page Release R.1.3 UK 35 3.12 Conversion to a different gas category 36 Instruction Manual BFC n Release R.1.3 UK 37 c Page Release R.1.3 UK 39 4 Filling and draining 4.1 Introduction 4.2 Filling the appliance 4.2.1 Filling unvented installations 4.2.2 Filling vented installations 4gis Release R.1.3 UK 41 4.3 Draining the 4.3.1 Draining unvented installations 4.3.2 Draining vented installations Page Release R.1.3 UK 43 5 The control panel 5.1 Introduction 5.2 Operating 44 Instruction Manual BFC 5gis 5.3 Explanation of the icons 5.4 ON/OFF switch of ThermoControl 5.5 Navigation buttons 5.6 PC connection. 6 Status of the appliance 6.1 Introduction 6.2 Operating modes 46 Instruction Manual BFC 6gis 6.3 Error conditions Release R.1.3 UK 47 6.4 Service condition Page Release R.1.3 UK 49 7 Starting up and shutting down 7.1 Introduction 7.2 Starting up 7.3 Shutting down 50 Instruction Manual BFC 7gis 7.3.1 Shut the appliance down for a brief period (OFF mode) 7.3.2 Disconnect the appliance from the mains 7.3.3 Shut the appliance down for a longer period Release R.1.3 UK 51 W S O D 7gis G O V and D S 8 Main menu 8.1 Introduction 8.2 Notational convention for menu-related instructions 54 Instruction Manual BFC 8.3 Switching into ON mode 8.4 Setting the water temperature 8.4.1 Setting the water temperature via SETPOINT MENU 8.4.2 Setting water temperature during ON mode Release R.1.3 UK 55 8.5 Week programme 8.5.1 Introduction 8.5.2 Starting up and shutting down the week program 8.5.3 Changing the appliances standard week program Page Release R.1.3 UK 57 8.5.4 Adding times to a week program 58 Instruction Manual BFC 8.5.5 Deleting times from a week program Page 60 Instruction Manual BFC 8.6 Extra period 8.6.1 Introduction 8.6.2 Programming an extra period Release R.1.3 UK 61 8.7 Settings 8.7.1 Introduction 8.7.2 Setting menu language 62 Instruction Manual BFC 8.7.3 Setting day and time 8.7.4 Displaying appliance specifications Page Page Release R.1.3 UK 65 9 Service program 9.1 Introduction 9.2 Setting the hysteresis 9.3 Displaying the error history 66 Instruction Manual BFC 9is 9.4 Displaying the appliance history 9.5 Display the selected 9.6 Setting the pump on/off 9.7 Setting the service interval Release R.1.3 UK 67 9.8 Setting the display contrast 9.9 Setting the backlight time 9.10 Setting the display scroll speed Page Release R.1.3 UK 69 10 Troubleshooting 10.1 Introduction Page Page Release R.1.3 UK 72 10.3 Troubleshooting table for displayed errors Page Page Page Page Page Page Page Page Page Page Release R.1.3 UK 83 gs 11 Maintenance frequency 11.1 Introduction 11.2 Determining service interval Page Release R.1.3 UK 85 12 Maintenance 12.1 Introduction cNote 12.2 Preparation for maintenance Page Page 12 s Release R.1.3 UK 89 13 Warranty (Certificate) 13.1 General warranty 13.2 Tank warranty 13.3 Installation and conditions of use 13.4 Exclusions 13 gis Page Appendices 92 Instruction Manual BFC Ais % A.2 Electrical diagram BFC A ! Page Index Release R.1.3 UK 95 IX Index A B C D IX gis N O P R