Status of the appliance | A.O. Smith 28 30 50 60 manual

gis

6

6.1Introduction

6.2Operating modes

OFF

13:45 Thursday 6ÉC

FROST PROTECTION ACTIVATED

Figure 6.1 Frost protection

ON

13:45 Thursday 67ÉC

Tset 75ÉC

Figure 6.2 ON

EXTRA

12:30 Thursday 76ÉC

TH 12:45 Tset 75ÉC

PERIOD ACTIVATED

Figure 6.3 Extra period

Introduction

Status of the appliance

Topics covered in this chapter:

•6.2 Operating modes;

•6.3 Error conditions;

•6.4 Service condition.

When running, the appliance has four basic operating modes, namely:

OFF

In this mode, the frost protection is activated. Figure 6.1 shows the display with the following information:

-line one: the text OFF;

-line two: the time, the day and alternately T1 and Tnet. See paragraph 2.3;

-lines three and four: the text FROST PROTECTION ACTIVATED.

ON

In this mode the appliance continuously fulfils the demand for hot water. Figure 6.2 shows the display with the following information:

-line one: the text ON;

-line two: the time, the day and alternately T1 and Tnet. See paragraph 2.3;

-line three: the programmed water temperature Tset;

-line four: is empty when the appliance is idle, or depending on the heating cycle, a text such as HEAT DEMAND. See ’7.4 The appliance’s heating cycle’.

EXTRA

In this mode, one extra period is programmed and activated. In this mode, the OFF or PROG position is temporarily overruled to fulfil a single period of heat demand. Once the period has passed, the appliance automatically returns to the previous operating mode. Figure 6.3 shows the display with the following information:

-line one: the text EXTRA;

-line two: the time, the day and alternately T1 and Tnet. See paragraph 2.3;

-line three: the switch-on time, and the related water temperature setting;

-line four: the text PERIOD ACTIVATED.

PROG

In this mode a preset week program is active, and the appliance responds continually to heat demand within the time periods set in the week program. There are two distinct situations possible in this mode:

Release R.1.3 UK

45

Image 45

A.O. Smith 28 30 50 60 service manual Status of the appliance, Introduction Operating modes

Contents

Release R.1.3 UK Your installer Trademarks CopyrightLiability More informationPage Gis Table of contents Control panel Filling and drainingStatus of the appliance Starting up and shutting down Troubleshooting Service programMaintenance frequency Maintenance Index Appendices Introduction What to do if you smell gas RegulationsAbout the appliance Symbol Target group Target groups Maintenance Forms of notationRemark Introduction Document Overview of thisOverview of this document Chapter Target groups Description Gis Functioning of the appliance Introduction Functional description of the applianceIntroduction Water temperature protection Gas control Pressure switch Ionisation rodAppliance’s heating cycle Protection for the appliance Pressure switch Water temperature protectionGas control 3 Fan Unvented installation Safety of the instal- lationVented installation Ionisation rod Introduction Packaging Environmental conditions Installation Maximum floor loading Humidity and ambient temperatureWater composition Working clearances Working clearances Environmental conditions Plan and elevation of the appliance Technical specifications Technical specifications DimensionsDime Description BFC Nsion Unit BFC VAC Gas data Installation diagramGeneral G30-30 mbar butane Unvented Installation Hot water side Water connections, Unvented Cold water sideCirculation pipe Condensation drainage Gas connection Water connections, VentedSee paragraph ’3.6.4 Condensation drainage’ See din Figure Dimension BFC Air supply and flue gas dischargeAir supply and flue gas discharge Concentric wall flue terminal Specification Description Concentric roof flue terminal Concentric roof flue terminal specifications Electrical connection PreparationPreparation Mains voltage Electrical connection Mains voltage Isolating Transformer Extra on mode switch Tank onContinuous pump Program-controlled pump Checking the supply Pressure and burner Connecting extra error signal Alarm OUTChecking the supply pressure and burner pressure Appliance Main menu Conversion to a different gas category Conversion to a different gas category Remove the burner as complete assembly Check the burner and supply pressure see paragraph 13 Conversion of gas control Installation Filling vented installations Filling the appliance Filling unvented installationsFilling and draining Filling the appliance Filling and draining Installation diagrams F d c Draining vented installations Draining unvented installationsDraining the appliance Draining the appliance Gis Introduction Operating Control panel Navigation buttons Explanation of the icons ON/OFF switch of ThermoControlPC connection Control panel Operating modes Error conditions Service condition Status of the applianceIntroduction Operating modes Status of the appliance Error conditions Service condition Service condition Gis Starting up and shutting down Open the gas valve see ’ .1 Installation diagrams’Introduction Starting up Shutting down Disconnect the appliance from the mains Shut the appliance down for a brief period OFF modeShut the appliance down for a longer period Starting up and shutting down Appliance’s heating cycle Appliance’s heating cycle 12 Ignition Notational convention for menu-related instructions Main menu Switching into on mode Setting the water temperature Setting the water temperature via Setpoint MenuSetting water temperature during on mode Week programme Introduction Starting up and shutting down the week programChanging the appliance’s standard week program Remark Setting the switch-on time Setting switch-off timeExample Setting program-controlled pump Setting the water temperatureAdding times to a week program Week programme 20 Period added Deleting times from a week program 23 week program options Programming an extra period Extra period Settings Setting menu languageSettings Displaying appliance specifications Remark Setting day and time 46 Main menu Gis Service program Setting the hysteresisDisplaying the error history Setting the service interval Setting the pump on/offService program Displaying the appliance history Setting the backlight time Setting the display contrastSetting the display scroll speed Setting the display contrast Service program Troubleshooting General errorsDisplayed errors Symptom Cause Solution Remark Gas smell Gas leak Troubleshooting table for general errors Symptom Cause Solution Remark Display is off See appendix ’A.2 Electrical diagram BFC’Water leakage Symptom Cause Solution Remark Explosive ignition Troubleshooting table for displayed errorsInsufficient or no hot Water S03 blocking error S02 blocking errorS04 blocking error S05 blocking error S13 blocking error S14 blocking errorS15 blocking error F02 lock out error Phase-sensitive. See ’3.10 Electrical connection’ Appliance specifications’ How to bleed air from the gas line, and measure the supply F07 lock out error F06 lock out errorF08 lock out error ’3.9 Air supply and flue gas discharge’ F10 lock out error Error F09 remains active in the event that the water Release R.1.3 UK Release R.1.3 UK E01 blocking error C04 blocking errorE03 blocking error E04 blocking error Determining service interval Maintenance frequency Maintenance frequency Remark Preparation for maintenance Maintenance Starting up Maintenance Cleaning condensation water discharge Descaling and cleaning the tankCleaning the burner Water-side mainte- nance Introduction Cleaning heat exchanger Cleaning the orifice12.4.3 Remark Finalising mainte- nance Warranty Certificate Warranty Certificate Week program card Appendices Appendices Electrical diagram Week program card Release R.1.3 UK Index IX Index IX Index 0306