See appendix ’A.2 Electrical diagram BFC’ | A.O. Smith 28 30 50 60

Warning

Maintenance may only be performed by a qualified service and maintenance engineer.

Table 10.1 General errors (Sheet 2 of 3)

is

Symptom	Cause	Solution		Remark

Display is off	Appliance is turned off.	Start-up the appliance. See ’7.2 Starting up’

	No electric power	1.	Check whether the mains switch is ON.	See appendix ’A.2 Electrical diagram BFC’.
	present	2.	Check that there is power to the mains switch.	If the error cannot be rectified, contact your installer.
		2.	Check that there is power to the mains switch.
		3.	Check whether the ON/OFF switch of the ThermoControl is ON
			(position I).
		4.	Check whether there is power to the electrical connection
			block.
		5.	The voltage measured must be 230 VAC (-15%, +10%).

	Defective fuse(s)	Replace fuse(s)		To replace the fuses you must contact your installer.

Water leakage	Leakage from one of	Tighten the threaded connection.		If the leak persists, consult your installer.
	the water connections
	(threaded).

	Condensation water	Check that the condensation water discharge is working properly.
	leakage	Rectify if necessary.

	Leakage from another	Trace the leak.
	nearby water
	appliance or pipe
	segment.

	Leakage from the	Consult the supplier and/or manufacturer.
	appliance’s tank.

Release R.1.3 UK

71

Image 71

A.O. Smith 28 30 50 60 Symptom Cause Solution Remark Display is off, See appendix ’A.2 Electrical diagram BFC’

Contents

Release R.1.3 UK Your installer More information CopyrightTrademarks LiabilityPage Gis Table of contents Starting up and shutting down Filling and drainingControl panel Status of the appliance Maintenance Service programTroubleshooting Maintenance frequency Index Appendices About the appliance IntroductionWhat to do if you smell gas Regulations Introduction Target groups Maintenance Forms of notationSymbol Target group Remark Chapter Target groups Description Overview of thisDocument Overview of this document Gis Introduction Functioning of the applianceIntroduction Functional description of the appliance Appliance’s heating cycle Protection for the appliance Water temperature protection Gas controlPressure switch Ionisation rod 3 Fan Water temperature protectionPressure switch Gas control Ionisation rod Safety of the instal- lationUnvented installation Vented installation Introduction Packaging Environmental conditions Installation Working clearances Humidity and ambient temperatureMaximum floor loading Water composition Working clearances Environmental conditions Plan and elevation of the appliance Technical specifications Unit BFC DimensionsTechnical specifications Dime Description BFC Nsion VAC G30-30 mbar butane Installation diagramGas data General Unvented Installation Condensation drainage Water connections, Unvented Cold water sideHot water side Circulation pipe See din Figure Water connections, VentedGas connection See paragraph ’3.6.4 Condensation drainage’ Air supply and flue gas discharge Dimension BFCAir supply and flue gas discharge Concentric wall flue terminal Specification Description Concentric roof flue terminal Concentric roof flue terminal specifications Preparation Mains voltage Electrical connectionPreparation Electrical connection Mains voltage Program-controlled pump Extra on mode switch Tank onIsolating Transformer Continuous pump Appliance Connecting extra error signal Alarm OUTChecking the supply Pressure and burner Checking the supply pressure and burner pressure Main menu Conversion to a different gas category Conversion to a different gas category Remove the burner as complete assembly Check the burner and supply pressure see paragraph 13 Conversion of gas control Installation Filling the appliance Filling the appliance Filling unvented installationsFilling vented installations Filling and draining Filling and draining Installation diagrams F d c Draining the appliance Draining unvented installationsDraining vented installations Draining the appliance Gis Introduction Operating Control panel Control panel Explanation of the icons ON/OFF switch of ThermoControlNavigation buttons PC connection Introduction Operating modes Operating modes Error conditions Service conditionStatus of the appliance Status of the appliance Error conditions Service condition Service condition Gis Shutting down Open the gas valve see ’ .1 Installation diagrams’Starting up and shutting down Introduction Starting up Starting up and shutting down Shut the appliance down for a brief period OFF modeDisconnect the appliance from the mains Shut the appliance down for a longer period Appliance’s heating cycle Appliance’s heating cycle 12 Ignition Notational convention for menu-related instructions Main menu Setting water temperature during on mode Switching into on mode Setting the water temperatureSetting the water temperature via Setpoint Menu Changing the appliance’s standard week program Remark Week programme IntroductionStarting up and shutting down the week program Example Setting the switch-on timeSetting switch-off time Week programme Setting the water temperatureSetting program-controlled pump Adding times to a week program 20 Period added Deleting times from a week program 23 week program options Programming an extra period Extra period Settings SettingsSetting menu language Displaying appliance specifications Remark Setting day and time 46 Main menu Gis Displaying the error history Service programSetting the hysteresis Displaying the appliance history Setting the pump on/offSetting the service interval Service program Setting the display contrast Setting the display contrastSetting the backlight time Setting the display scroll speed Service program Displayed errors TroubleshootingGeneral errors Symptom Cause Solution Remark Gas smell Gas leak Troubleshooting table for general errors Water leakage Symptom Cause Solution Remark Display is offSee appendix ’A.2 Electrical diagram BFC’ Water Troubleshooting table for displayed errorsSymptom Cause Solution Remark Explosive ignition Insufficient or no hot S05 blocking error S02 blocking errorS03 blocking error S04 blocking error S15 blocking error S13 blocking errorS14 blocking error F02 lock out error Phase-sensitive. See ’3.10 Electrical connection’ Appliance specifications’ How to bleed air from the gas line, and measure the supply ’3.9 Air supply and flue gas discharge’ F06 lock out errorF07 lock out error F08 lock out error F10 lock out error Error F09 remains active in the event that the water Release R.1.3 UK Release R.1.3 UK E04 blocking error C04 blocking errorE01 blocking error E03 blocking error Determining service interval Maintenance frequency Maintenance frequency Remark Preparation for maintenance Maintenance Starting up Maintenance Water-side mainte- nance Introduction Descaling and cleaning the tankCleaning condensation water discharge Cleaning the burner Remark Finalising mainte- nance Cleaning the orificeCleaning heat exchanger 12.4.3 Warranty Certificate Warranty Certificate Week program card Appendices Appendices Electrical diagram Week program card Release R.1.3 UK Index IX Index IX Index 0306