Manuals / Agilent Technologies / Home Audio / Stereo System

Agilent Technologies Agilent 35670A manual Selecting Measurement Parameters

Models: Agilent 35670A

1 82

Download 82 pages 27.58 Kb

Page 39

Selecting Measurement Parameters

AGILENT 35670A

Supplemental Operator’s Guide

Section 14 : Comparing Two-Channel Real-Time Spectra with Recalled Data

Compare two channels of real-time data with spectra stored in registers using the UPPR/LOWR FRNT/BACK display format of the AGILENT 35670A. Note that the real-time data should be measured with the same frequency and resolution as the stored data if valid, direct comparisons are desired.

Preset the analyzer as follows:

•Press the green [Preset] hardkey

•Press [DO PRESET] softkey (F1).

•Press the yellow [Pause/Cont] hardkey if desired.

Selecting Measurement Parameters

Refer to the section entitled “Measuring Dual Channel Spectra” to set up span, ranges, coupling, averaging, and windowing. Transducer parameters set up is described in the section “Measuring with Transducers.”

Displaying Dual-Channel Spectra Compared with Recalled Data

The results of a dual-channel measurement are compared to recalled spectra in data registers via the following steps:

•Press the [Disp Format] hardkey.

•Press the [UPPR/LOWR FRNT/BACK] softkey (F5).

•Press the [Active Trace] hardkey.

•Press the [A] softkey (F1).

•Press the [Meas Data] hardkey.

•	Press the	[CHANNEL 1 2 3 4] softkey (F1) until 1 is highlighted.
•	Press the	[PWR SPEC CHANNEL 1] softkey (F3)

•Press the [Active Trace] hardkey again.

•Press the [B] softkey (F2).

•Press the [Meas Data] hardkey.

•Press the [MORE CHOICES] softkey (F9).

•Press the [DATA REGISTER] softkey (F8).

•Press the [D1] softkey (F1).

•Press the [Active Trace] hardkey.

•Press the [C] softkey (F1).

•Press the [Meas Data] hardkey.

•	Press the	[CHANNEL 1 2 3 4] softkey (F1) until 2 is highlighted.
•	Press the	[PWR SPEC CHANNEL 2] softkey (F3).

•Press the [Active Trace] hardkey again.

•Press the [D] softkey (F2).

•Press the [Meas Data] hardkey.

35

Image 39

Agilent Technologies Agilent 35670A manual Selecting Measurement Parameters

Contents

Supplemental Operator’s Guide for the Agilent 35670A Dynamic Signal AnalyzerAGILENT 35670A Supplemental Operator’s Guide SECTION 13 ORDER DOMAIN RESULTS IN LIST MODE SECTION 24 PLOTTING AND PRINTING TRACE DATA Section 1 Turning On the AGILENT 35670A Freq Inst ModeMeas Data Trac Coord Coord AUsing ICP-TypeTransducers with the AGILENT 35670A Using Transducers with External PreamplifiersSection 3 Measuring with Transducers Specifying Transducer Sensitivity and Units Setting Up Transducer Units for Displacement Selecting Single Channel OperationSelecting Frequency Span Frequency Spans Available for the AGILENT 35670A Quantifying Power Spectrum Results Frequency Zooming to Increase Resolution Maximizing Dynamic RangeSection 5 Improving Measurement Results Averaging to Reduce Measurement Variance AGILENT 35670A Supplemental Operator’s Guide Selecting Single Channel Operation AGILENT 35670A Supplemental Operator’s GuideDisplaying Time Waveforms Selecting Time Record LengthEvent Triggering Quantifying Time Trace Results Selecting Frequency Span Presetting the AnalyzerSelecting Dual Channel Operation Section 7 Measuring Dual Channel SpectraUsing Markers with Dual Channel Measurements Coupled Markers with Peak Tracking Coupled MarkersMaximizing Dynamic Range Dual Channel AveragingAGILENT 35670A Supplemental Operator’s Guide Selecting Time Record Length Displaying Dual Time WaveformsSection 9 Measuring Dual Channel Time Waveforms Selecting Dual Channel OperationTriggering a Dual-ChannelTime Measurement Arming Dual Channel Time MeasurementsTrigger Delay Using Markers with Dual Channel Time Measurements AGILENT 35670A Supplemental Operator’s Guide Setting Up the Transducer Parameters Setting Up Input Range Choosing a Preliminary Frequency SpanSpecifying Trigger Parameters WAITING FOR CH 1 TRIGGER Setting Up Time DisplaysUsing Force/Response Windows Averaging Displaying Hammer Test ResultsAGILENT 35670A Supplemental Operator’s Guide Delay = 01.T ForceWidth = T ExponentialDecay = T Changing Frequency SpanAGILENT 35670A Supplemental Operator’s Guide Prepare the order results list as follows AGILENT 35670A Supplemental Operator’s GuideSection 13 Order Domain Results in List Mode Prepare the order display as followsTo start taking measurements AGILENT 35670A Supplemental Operator’s GuideSelecting Measurement Parameters Recalling the Spectra from Non-VolatileRAM Recalling the Spectra from DiskScaling the Displays Using Markers to Compare Selecting Measurement Parameters Setting Up the Waterfall DisplaySection 15 Waterfall Spectra at Time Intervals Selecting Single Channel OperationUsing Slice Markers with Waterfall Data Setting Up Time Step ArmAGILENT 35670A Supplemental Operator’s Guide Setting Up the Tachometer Specifying the Start RPMSection 16 Waterfall Spectra at RPM Intervals Scaling the Display Starting and Pausing a MeasurementAGILENT 35670A Supplemental Operator’s Guide Accelerometer Polarity AGILENT 35670A Supplemental Operator’s Guide Set up triggering on Channel 1 to 5% of rangeFor accelerometers with opposite polarity Set up the AGILENT 35670AAGILENT 35670A Supplemental Operator’s Guide For accelerometers with the same polaritySet up display Set up trace coordinates as peak-to-peakmilAGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide Enter Channel 1 input parameters Preset the AGILENT 35670AAGILENT 35670A Supplemental Operator’s Guide Connect the transducersSet up display parameters AGILENT 35670A Supplemental Operator’s GuideChoose measurement parameters AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide Viewing Results Using Real and Imaginary TracesAssessing Measurement Quality Preset the AGILENT 35670A Set up Trace B to measure velocity in inch/s 0-pkAGILENT 35670A Supplemental Operator’s Guide Press the XDCR UNIT CONVERT softkey F4 AGILENT 35670A Supplemental Operator’s GuidePress the Trace Coord hardkey Press the Y UNITS softkey F8AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide When the run-upand run-downis completedCharacterizing the External Trigger Specify User Levels for TriggeringSet up a non-TTLtrigger as follows Setting Up External TriggerAcquire and Display the Trigger Signal Characterize the Trigger SignalAGILENT 35670A Supplemental Operator’s Guide Set up measurement parametersSaving Trace to 3.5” Disk Confirming Contents of 3.5” Disk FileTo return to the Trace view Confirming Contents of NV-RAMSaving Trace to Non-VolatileRAM NV-RAM AGILENT 35670A Supplemental Operator’s GuideRecall Trace Data from Non-VolatileRAM NV-RAM Recall Trace From 3.5” DiskAGILENT 35670A Supplemental Operator’s Guide Generating Output with the AGILENT 35670A Plotting the DisplaySection 24 Plotting and Printing Trace Data Plot the Trace Printing the DisplayAGILENT 35670A Supplemental Operator’s Guide Check the Plot/Print DestinationSection 25 Importing Plots into Microsoft Word Plot to a File Using the AGILENT 35670A Section 28 Precautions to Prevent Loss of Data Measuring Acceleration, Displaying Displacement Converting Frequency Response Units to Compliance Math Functions and XDCR UNIT CONVERTNow display the function F1 on Trace B AGILENT 35670A Supplemental Operator’s GuideAGILENT 35670A Supplemental Operator’s Guide above the track number AGILENT 35670A Supplemental Operator’s GuideSection Section