Manuals / Agilent Technologies / Home Audio / Stereo System

Agilent Technologies Agilent 35670A manual AGILENT 35670A Supplemental Operator’s Guide

Models: Agilent 35670A

1 82

Download 82 pages 27.58 Kb

Page 55

AGILENT 35670A

Supplemental Operator’s Guide

•Attach one end of stinger to shaker and one end to force transducer

•Connect amplifier output to shaker

•Connect amplifier input to AGILENT 35670A source

Connect the transducers

•Connect force transducer to Channel 1

•Connect accelerometer to Channel 2

Preset the AGILENT 35670A

•Turn on the AGILENT 35670A, or

•Press the green [Preset] hardkey

•Press the yellow [Pause/Cont] hardkey if desired.

Enter Channel 1 input parameters

•Press the [Input] hardkey

•Press [CH1 AUTO UP ONLY] softkey (F5).

•Press [FRONT END CH1 SETUP] softkey (F7).

• Press [ICP SUPLY ON OFF] softkey (F8) until ON is highlighted.

•Press the [Input] hardkey

•Press [XDCR UNIT CH1 SETUP] softkey (F8)

•Press the [XDCR SENSITVTY] softkey (F6).

•Enter 8, then press the [mV/EU] softkey (F2).

• Toggle the [XDCR UNIT ON OFF] softkey (F4) until ON is highlighted.

•Press the [XDCR UNIT LABEL] softkey (F7).

•Press the [MORE CHOICES] softkey (F9).

•Select the [ lb ] softkey (F6).

Enter Channel 2 input parameters

•Press the [Input] hardkey

• Press [CHANNEL 1 2 3 4] softkey (F1) until 2 is highlighted.

•Press [CH2 AUTO UP ONLY] softkey (F5).

•Press [FRONT END CH2 SETUP] softkey (F7).

•Press [ICP SUPLY ON OFF] softkey (F8) until ON is highlighted.

•Press the [Input] hardkey

•Press [XDCR UNIT CH2 SETUP] softkey (F8)

•Press the [XDCR SENSITVTY] softkey (F6).

•Enter 10.2, then press the [mV/EU] softkey (F2).

• Toggle the [XDCR UNIT ON OFF] softkey (F4) until ON is highlighted.

•Press the [XDCR UNIT LABEL] softkey (F7).

•Select the [ g ] softkey (F2).

51

Image 55

Agilent Technologies Agilent 35670A manual AGILENT 35670A Supplemental Operator’s Guide, Connect the transducers

Contents

Supplemental Operator’s Guide for the Agilent 35670A Dynamic Signal AnalyzerAGILENT 35670A Supplemental Operator’s Guide SECTION 13 ORDER DOMAIN RESULTS IN LIST MODE SECTION 24 PLOTTING AND PRINTING TRACE DATA Section 1 Turning On the AGILENT 35670A Freq Inst ModeMeas Data Trac Coord Coord AUsing Transducers with External Preamplifiers Using ICP-TypeTransducers with the AGILENT 35670ASection 3 Measuring with Transducers Specifying Transducer Sensitivity and Units Selecting Single Channel Operation Setting Up Transducer Units for DisplacementSelecting Frequency Span Frequency Spans Available for the AGILENT 35670A Quantifying Power Spectrum Results Maximizing Dynamic Range Frequency Zooming to Increase ResolutionSection 5 Improving Measurement Results Averaging to Reduce Measurement Variance AGILENT 35670A Supplemental Operator’s Guide Selecting Single Channel Operation AGILENT 35670A Supplemental Operator’s GuideDisplaying Time Waveforms Selecting Time Record LengthEvent Triggering Quantifying Time Trace Results Selecting Frequency Span Presetting the AnalyzerSelecting Dual Channel Operation Section 7 Measuring Dual Channel SpectraUsing Markers with Dual Channel Measurements Coupled Markers with Peak Tracking Coupled MarkersMaximizing Dynamic Range Dual Channel AveragingAGILENT 35670A Supplemental Operator’s Guide Selecting Time Record Length Displaying Dual Time WaveformsSection 9 Measuring Dual Channel Time Waveforms Selecting Dual Channel OperationTriggering a Dual-ChannelTime Measurement Arming Dual Channel Time MeasurementsTrigger Delay Using Markers with Dual Channel Time Measurements AGILENT 35670A Supplemental Operator’s Guide Setting Up the Transducer Parameters Choosing a Preliminary Frequency Span Setting Up Input RangeSpecifying Trigger Parameters WAITING FOR CH 1 TRIGGER Setting Up Time DisplaysUsing Force/Response Windows Averaging Displaying Hammer Test ResultsAGILENT 35670A Supplemental Operator’s Guide Delay = 01.T ForceWidth = T ExponentialDecay = T Changing Frequency SpanAGILENT 35670A Supplemental Operator’s Guide Prepare the order results list as follows AGILENT 35670A Supplemental Operator’s GuideSection 13 Order Domain Results in List Mode Prepare the order display as followsTo start taking measurements AGILENT 35670A Supplemental Operator’s GuideSelecting Measurement Parameters Recalling the Spectra from Non-VolatileRAM Recalling the Spectra from DiskScaling the Displays Using Markers to Compare Selecting Measurement Parameters Setting Up the Waterfall DisplaySection 15 Waterfall Spectra at Time Intervals Selecting Single Channel OperationUsing Slice Markers with Waterfall Data Setting Up Time Step ArmAGILENT 35670A Supplemental Operator’s Guide Specifying the Start RPM Setting Up the TachometerSection 16 Waterfall Spectra at RPM Intervals Scaling the Display Starting and Pausing a MeasurementAGILENT 35670A Supplemental Operator’s Guide Accelerometer Polarity AGILENT 35670A Supplemental Operator’s Guide Set up triggering on Channel 1 to 5% of rangeFor accelerometers with opposite polarity Set up the AGILENT 35670AAGILENT 35670A Supplemental Operator’s Guide For accelerometers with the same polaritySet up trace coordinates as peak-to-peakmil Set up displayAGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide Enter Channel 1 input parameters Preset the AGILENT 35670AAGILENT 35670A Supplemental Operator’s Guide Connect the transducersAGILENT 35670A Supplemental Operator’s Guide Set up display parametersChoose measurement parameters AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide Viewing Results Using Real and Imaginary TracesAssessing Measurement Quality Set up Trace B to measure velocity in inch/s 0-pk Preset the AGILENT 35670AAGILENT 35670A Supplemental Operator’s Guide Press the XDCR UNIT CONVERT softkey F4 AGILENT 35670A Supplemental Operator’s GuidePress the Trace Coord hardkey Press the Y UNITS softkey F8AGILENT 35670A Supplemental Operator’s Guide AGILENT 35670A Supplemental Operator’s Guide When the run-upand run-downis completedCharacterizing the External Trigger Specify User Levels for TriggeringSet up a non-TTLtrigger as follows Setting Up External TriggerAcquire and Display the Trigger Signal Characterize the Trigger SignalAGILENT 35670A Supplemental Operator’s Guide Set up measurement parametersSaving Trace to 3.5” Disk Confirming Contents of 3.5” Disk FileTo return to the Trace view Confirming Contents of NV-RAMSaving Trace to Non-VolatileRAM NV-RAM AGILENT 35670A Supplemental Operator’s GuideRecall Trace Data from Non-VolatileRAM NV-RAM Recall Trace From 3.5” DiskAGILENT 35670A Supplemental Operator’s Guide Plotting the Display Generating Output with the AGILENT 35670ASection 24 Plotting and Printing Trace Data Plot the Trace Printing the DisplayAGILENT 35670A Supplemental Operator’s Guide Check the Plot/Print DestinationSection 25 Importing Plots into Microsoft Word Plot to a File Using the AGILENT 35670A Section 28 Precautions to Prevent Loss of Data Measuring Acceleration, Displaying Displacement Converting Frequency Response Units to Compliance Math Functions and XDCR UNIT CONVERTNow display the function F1 on Trace B AGILENT 35670A Supplemental Operator’s GuideAGILENT 35670A Supplemental Operator’s Guide above the track number AGILENT 35670A Supplemental Operator’s GuideSection Section