Manuals / Analog Devices / Computer Equipment / Network Card

Analog Devices ADSP-TS201S specifications Ordering Guide, Operating Voltage Option Description

Models: ADSP-TS201S

1 48

Download 48 pages 43.31 Kb

Page 46

Image 46

ADSP-TS201S

ORDERING GUIDE

	Temperature	Instruction	On-Chip		Package	Package
Model	Range1	Rate2	DRAM	Operating Voltage	Option	Description
ADSP-TS201SABP-060	–40°C to +85°C	600 MHz	24M bit	1.20 VDD, 2.5 VDD_IO, 1.6 VDD_DRAM	BP-576	576-Ball BGA_ED
ADSP-TS201SABP-050	–40°C to +85°C	500 MHz	24M bit	1.05 VDD, 2.5 VDD_IO, 1.5 VDD_DRAM	BP-576	576-Ball BGA_ED
ADSP-TS201SYBP-050	–40°C to +105°C	500 MHz	24M bit	1.05 VDD, 2.5 VDD_IO, 1.5 VDD_DRAM	BP-576	576-Ball BGA_ED
ADSP-TS201SABPZ0603	–40°C to +85°C	600 MHz	24M bit	1.20 VDD, 2.5 VDD_IO, 1.6 VDD_DRAM	BP-576	576-Ball BGA_ED
ADSP-TS201SABPZ0503	–40°C to +85°C	500 MHz	24M bit	1.05 VDD, 2.5 VDD_IO, 1.5 VDD_DRAM	BP-576	576-Ball BGA_ED
ADSP-TS201SYBPZ0503	–40°C to +105°C	500 MHz	24M bit	1.05 VDD, 2.5 VDD_IO, 1.5 VDD_DRAM	BP-576	576-Ball BGA_ED

1Represents case temperature.

2The instruction rate is the same as the internal processor core clock (CCLK) rate.

3 Z = Pb-free part.

Rev. C Page 46 of 48 December 2006

Page 46

Image 46

Analog Devices ADSP-TS201S specifications Ordering Guide, Temperature Instruction On-Chip Package Model Range1 Rate2

Contents

ADSP-TS201S ADSP-TS201S Benchmark Speed Cycles General-Purpose Algorithm Benchmarks at 600 MHzClock FIR filter per real tap 83 nsData Alignment Buffer DAB Dual Compute BlocksDual Integer ALU Ialu Interrupt Controller Program SequencerDSP Memory Flexible Instruction SetExternal Port OFF-CHIP MEMORY/PERIPHERALS Interface Internal SpaceMultiprocessor Interface DMA ControllerHost Interface Sdram ControllerDMA controller provides these additional features No Boot, Run from Memory Addresses Timer and GENERAL-PURPOSE I/OReset and Booting Link Ports LvdsFiltering Reference Voltage and Clocks Power DomainsDevelopment Tools Evaluation KIT Additional InformationSclk Ratio Pin Definitions-Clocks and ResetSignal Type Term Description RatioPin Definitions-External Port Bus Controls ACK T/ODSignal Type Pin Definitions-External Port ArbitrationSample the data instead of the TigerSHARC Pin Definitions-External Port DMA/FlybyDSP performs DMA transfers according to the DMA MakesHdqm Pin Definitions-External Port Sdram ControllerLdqm SDA10Pin Definitions-Flags, Interrupts, and Timer Pin Definitions-JTAG Port Signal Type Term DescriptionCONTROLIMP1 Pin Definitions-Link PortsCONTROLIMP0 DS1DS2-0 Drive Output Pins Strength Impedance Pin Definitions-Power, Ground, and ReferenceDriver Mode Impedance Control SelectionType at Signal Reset Pin Definitions-I/O Strap PinsPin Rstin = Operating Conditions SclkvrefMaximum Duty Electrical CharacteristicsMaximum Duty Cycle for Input Transient Voltage VIN Max VIN Min Cycle2Absolute Maximum Ratings Package InformationESD Sensitivity Package Brand InformationGeneral AC Timing Timing SpecificationsAC Asynchronous Signal Specifications Reference Clocks-Core Clock Cclk Cycle TimeSclkrat = 5⋅, 7⋅ Parameter Description Min Max Unit Reference Clocks-System Clock Sclk Cycle TimeReference Clocks-JTAG Test Clock TCK Cycle Time Parameter Description Min Max UnitPower-Up Timing1 Power-Up Reset TimingNormal Reset Timing On-Chip Dram Refresh1AC Signal Specifications OutputDisable MaxJtag SYS 11 Jtag System Pins +2.5 +10.0 +12.0 DS2-0 Static Pins-Must Be ConstantStrap Pins Strap SYS 9Parameter Description Test Conditions Min Max Unit Link Port Lvds Transmit Electrical CharacteristicsLink Port Lvds Receive Electrical Characteristics VODLink Port-Data Out Timing Parameter Description Min Max UnitLink Ports-Output Clock Link Ports-Transmission End and Stops Link Port-Data In Timing LxBCMPI Hold FigureLink Ports-Data Input Setup and Hold1 Output Drive Currents Typical Drive Currents at StrengthOutput Disable Time Test ConditionsOutput Enable Time Capacitive LoadingTimes Andfall Rise Fall Time Environmental Conditions Thermal CharacteristicsThermal Characteristics for 25 mm × 25 mm Package Parameter Condition Typical UnitBall Bgaed PIN Configurations Ball No Signal Name Ball 25 mm × 25 mm Bgaed Ball AssignmentsL0DATI1N Sdcke SCLKRAT1L0ACKO L0DATI3NDS1 CONTROLIMP1 TDO FLAG3 DS2 Enedreg TCKID2 TDI TMR0E L1CLKINNPackage Ball Attach Type Solder Mask Opening Ball Pad Size Surface Mount DesignBGA Data for Use with Surface Mount Design Ball Bgaed Nonsolder Mask Defined Nsmd Mm diameter BP-576Ordering Guide Temperature Instruction On-Chip Package Model Range1 Rate2Operating Voltage Option Description Rev. C Page 47 of 48 December Rev. C Page 48 of 48 December

ADSP-TS201S

ORDERING GUIDE

Temperature

Instruction

On-Chip

Package

Model

Range1

Rate2

DRAM

Operating Voltage

Option

Description

ADSP-TS201SYBP-050