Normal Reset Timing | Analog Devices ADSP-TS201S specification

ADSP-TS201S

Table 27. Normal Reset Timing

Parameter						Min	Max	Unit
Timing Requirements
tRST_IN		Asserted				2		ms
	RST_IN
tSTRAP		Deasserted After Strap Pins Stable				1.5		ms
	RST_IN
Switching Characteristic
tRST_OUT			Deasserted After		Deasserted	1.5		ms
	RST_OUT			RST_IN

RST_IN

RST_OUT

STRAP PINS

tRST_IN

tRST_OUT

tSTRAP

Figure 14. Normal Reset Timing

Table 28. On-Chip DRAM Refresh1

Parameter		Min	Max	Unit
Timing Requirement
tREF	On-chip DRAM Refresh Period		1.56	μs

1For more information on setting the refresh rate for the on-chip DRAM, refer to the ADSP-TS201 TigerSHARC Processor Programming Reference.

Rev. C Page 27 of 48 December 2006

Page 27

Image 27

Analog Devices ADSP-TS201S specifications Normal Reset Timing, On-Chip Dram Refresh1

Contents

ADSP-TS201S ADSP-TS201S FIR filter per real tap 83 ns General-Purpose Algorithm Benchmarks at 600 MHzClock Benchmark Speed Cycles Dual Compute Blocks Data Alignment Buffer DABDual Integer ALU Ialu Flexible Instruction Set Program SequencerDSP Memory Interrupt Controller Internal Space External Port OFF-CHIP MEMORY/PERIPHERALS Interface Sdram Controller DMA ControllerHost Interface Multiprocessor Interface DMA controller provides these additional features Link Ports Lvds Timer and GENERAL-PURPOSE I/OReset and Booting No Boot, Run from Memory Addresses Power Domains Filtering Reference Voltage and ClocksDevelopment Tools Additional Information Evaluation KIT Ratio Pin Definitions-Clocks and ResetSignal Type Term Description Sclk Ratio ACK T/OD Pin Definitions-External Port Bus Controls Pin Definitions-External Port Arbitration Signal Type Makes Pin Definitions-External Port DMA/FlybyDSP performs DMA transfers according to the DMA Sample the data instead of the TigerSHARC SDA10 Pin Definitions-External Port Sdram ControllerLdqm Hdqm Pin Definitions-JTAG Port Signal Type Term Description Pin Definitions-Flags, Interrupts, and Timer DS1 Pin Definitions-Link PortsCONTROLIMP0 CONTROLIMP1 Impedance Control Selection Pin Definitions-Power, Ground, and ReferenceDriver Mode DS2-0 Drive Output Pins Strength Impedance Pin Definitions-I/O Strap Pins Type at Signal ResetPin Rstin = Sclkvref Operating Conditions VIN Max VIN Min Cycle2 Electrical CharacteristicsMaximum Duty Cycle for Input Transient Voltage Maximum Duty Package Brand Information Package InformationESD Sensitivity Absolute Maximum Ratings Reference Clocks-Core Clock Cclk Cycle Time Timing SpecificationsAC Asynchronous Signal Specifications General AC Timing Parameter Description Min Max Unit Reference Clocks-System Clock Sclk Cycle TimeReference Clocks-JTAG Test Clock TCK Cycle Time Sclkrat = 5⋅, 7⋅ Parameter Description Min Max Unit Power-Up Reset Timing Power-Up Timing1 On-Chip Dram Refresh1 Normal Reset Timing OutputDisable Max AC Signal Specifications Strap SYS 9 DS2-0 Static Pins-Must Be ConstantStrap Pins Jtag SYS 11 Jtag System Pins +2.5 +10.0 +12.0 VOD Link Port Lvds Transmit Electrical CharacteristicsLink Port Lvds Receive Electrical Characteristics Parameter Description Test Conditions Min Max Unit Parameter Description Min Max Unit Link Port-Data Out Timing Link Ports-Output Clock Link Ports-Transmission End and Stops LxBCMPI Hold Figure Link Port-Data In Timing Link Ports-Data Input Setup and Hold1 Typical Drive Currents at Strength Output Drive Currents Test Conditions Output Disable Time Capacitive Loading Output Enable Time Times Andfall Rise Fall Time Parameter Condition Typical Unit Thermal CharacteristicsThermal Characteristics for 25 mm × 25 mm Package Environmental Conditions Ball Bgaed PIN Configurations Ball 25 mm × 25 mm Bgaed Ball Assignments Ball No Signal Name L0DATI3N Sdcke SCLKRAT1L0ACKO L0DATI1N L1CLKINN DS2 Enedreg TCKID2 TDI TMR0E DS1 CONTROLIMP1 TDO FLAG3 Ball Bgaed Nonsolder Mask Defined Nsmd Mm diameter BP-576 Surface Mount DesignBGA Data for Use with Surface Mount Design Package Ball Attach Type Solder Mask Opening Ball Pad Size Temperature Instruction On-Chip Package Model Range1 Rate2 Ordering GuideOperating Voltage Option Description Rev. C Page 47 of 48 December Rev. C Page 48 of 48 December

ADSP-TS201S

Table 27. Normal Reset Timing

Parameter

Deasserted

Figure 14. Normal Reset Timing

Table 28. On-Chip DRAM Refresh1

Parameter

On-chip DRAM Refresh Period