AT&T 585-300-903 manual 11-22DCP Mode 2 Installation and Administration

11-22DCP Mode 2 Installation and Administration

________________________________________________________________________________________________

________________________________________________________________________________________________

3.Procedure 100, Word 2 (for the digital side):

a.Enter the trunk group number (tgroup1) in Field 1.

b.Set the data rate for each speed optioned for the data modules in the modem pool in Fields 2 through 10.

NOTE

A data rate of 64 Kbps should always be translated for the modem pool in addition to the data rates optioned on the data module; this will ensure that a modem pool is selected when an incoming data call is directed to an AUDIX DCP port. If 64 Kbps is not translated, the modem-pool setup may not work, or may not recover after a failure.

c.Set Synchronous to 0 for asynchronous operation (Field 11 = 0).

d.Set Duplex to 0 for full duplex (Field 12 = 0).

e.Set Modem Pool Mode - Originate to 1 (Field 13 = 1).

f.Set Modem Pool Mode - Answer to 1 (Field 14 = 1).

g.Set Modem Pool - Modem Type to 1 (Field 15 = 1).

h.Set Modem Pool - Clock to 0 (Field 16 = 0).

i.Set Modem Pool - First Choice to 1 (Field 17 = 1).

j.Set Test Type to 0 (to turn off periodic on-line testing) or 1 (to allow periodic on-line testing) (Field 18). Currently only R2V3 systems should have Field 18 set to 1. On other systems, Field 18 should be 0.

k.Set Host Access Clock to 0 (Field 19 = 0).

______________________________________________________________________________________

⎜

Wd

⎜

1

⎜

2-10

⎜

11

⎜

12

⎜

13

⎜

14

⎜

15

⎜

16

⎜

17

⎜

18

⎜

19

⎜

PROC

⎜

⎜

2

⎜

tgroup1

⎜

*

⎜

0

⎜

0

⎜

1

⎜

1

⎜

1

⎜

0

⎜

1

⎜

$

⎜

0

⎜

100

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

*= data rate (translate 64 Kbps in addition to optioned rates, usually 9600 bps) $ = test type (see item j above)

4.Procedure 100, Word 1 (for the analog side):

a.Enter the trunk group number (tgroup2) in Field 1. A dial access code is not required (Fields 2 through 5).

b.Set Trunk Type to 101 (Field 6 = 101).

c.Set Dial Access Restriction to 0 (Field 7 = 0).

d.Set CO Line Appearance to 0 (Field 8 = 0).

______________________________________________________________________________________

⎜

Wd

⎜

1

⎜

2

⎜

3

⎜

4

⎜

5

⎜

6

⎜

7

⎜

8

⎜

PROC

⎜

⎜

1

⎜

tgroup2

⎜

⎜

⎜

⎜

⎜

101

⎜

0

⎜

0

⎜

100

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜

⎜