Possible storage Configurations, Scsi | ATTO Technology 2700C

efficiently managing Write commands between host and a tape device. Using the iPBridge results in a higher throughput and shorter backup times compared to native Fibre tape or direct attached SCSI tape libraries.

Advanced Diagnostics: software event-logging capability time and date stamped by the real time clock. You can also determine numerous status and current configuration parameters.

ATTO ExpressNAV: a web-based management application that allows all of the configurable settings for the iPBridge to be defined, viewed and edited.

Connectivity, infrastructure solutions The topology of a heterogeneous Storage Area Network shown below demonstrates the critical role ATTO products play in the design and implementation of a SAN. Whether your application needs are data-intensive or band- width intensive, you need to store and manage that data and then deliver it to end-users efficiently. ATTO products have been engineered with the highest performance and lowest cost available today.

Possible storage

configurations

Ethernet

Fibre Channel

SCSI

GbE network

ATTO iPBridge 2700

ATTO Celerity FC

storage adapter

GbE Switch

4-Gb FC Switch

ATTO FibreCenter Hub

ATTO ExpressPCI

FC storage adapter

ATTO FibreBridge 2400	ATTO FibreBridge	embedded
		embedded
		ATTO iPBridge
		1500/1550/2500
		SCSI Tape Library

SCSI Tape Library	FC model SCSI model	ATTO ExpressPCI
	ATTO Diamond Storage Array	SCSI storage adapter

2 iPBridge 2700C/R/D

Image 11

ATTO Technology 2700C operation manual Possible storage Configurations, Scsi

Contents

Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Alternative interface options TroubleshootingAtto ExpressNAV pages Updating firmware Diagnostic commands CLI commands summary General use commandsMaintenance commands ISCSI commands Serial port configuration commandsFibre Channel configuration commands Ethernet commands Appendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Gigabit Ethernet GbE a transmission Atto iPBridge 2700 features, benefitsEmbedded software features Atto iPBridge 2700 provides storage options Scsi Possible storage Configurations Atto iPBridge 2700R/D Installation instructions Front label side Back connector side Installation Atto iPBridge 2700R/D Serial management header Atto iPBridge 2700CEthernet interface Fibre Channel interface Faceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP address Map devices automatically Default target nodeTarget management Target names Multiple target nodes Automatically configure multiple targetsManually configure multiple target nodes Chap to control access different Chap Physical connections Initiator/Host to Network Mapping default vs. multiple target nodes Installation mapping Page Installation mapping Click Time & Date Additional configurationsCreate a read only password or username Set the Real Time Clock Snmp protocol Set up a Vlan Virtual Local Area Network Open an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Manual Target Management iSCSI Target Management Bridge ConfigurationFirmware Update Advanced CLI Configuration Preliminary steps Using Atto ExpressNAVUsing FTP over GbE Updating firmware Firmware update Check the event and trace logs TroubleshootingInside out method Check the Host Event Log Exhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devices Check components Check iPBridge product versions and update firmwareCheck host versions Checking the iSCSI Host Adapter or NIC Checking the LAN/WAN Checking the iPBridge Ethernet ports Performance IssuesChecking the iSCSI OS driver Checking the Operating System Optimizing Atto ExpressNAV in Internet Explorer Checking the Ethernet host adapter or NICChecking applications Checking the host system Type iPBridge in the New Connection dialog box Alternative interface optionsUse the serial port or header Use Telnet Exhibit 6.0-1 Start up messages Ready Command conventions Symbol IndicatesFCTargets command CLI provides ASCII-based interface CLI Error Messages Command Defaults Example CLI commands summary Rmon Sntp Alternative interfaces CLI General use commands VerboseMode Username Maintenance commands TailEventLog SpeedWriteDefaultSNTPServer SpeedWrite Diagnostic commands EmailNotify DumpEventLogDumpTraceLog EmailFromAddress SerialNumber IsReservedPing RouteDisplay TraceLogFilter TemperatureSNMPTraps TraceLog SerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPassword ISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Cable length Cable size Appendix a CablingFibre Channel connections Ethernet connections Term Definition Appendix B Glossary FCC Standards Radio and Television Interference Appendix C Safety standards and compliances Vi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information