ISCSIWANIPAddress, ISNSLoginControl | ATTO Technology 2700C instruction

iSCSIWANIPAddress

Sets the IP address reported from the sendtargets command. Setting the address to 0.0.0.0 will cause the unit to report the LAN IP address.

Set syntax: set iSCSIWANIPAddress [dp[n] all] [xxx.xxx.xxx.xxx]

Get syntax: get iSCSIWANIPAddress [dp[n] all]

iSNSLoginControl

Specifies whether the iPBridge will delegate its access control/authorization to an iSNS server.

Note: iSNSLoginControl cannot be used with AccessControl

Default: disabled

Set syntax: set iSNSLoginControl [enabled disabled] Requires a SaveConfiguration command

Get syntax: get iSNSLoginControl

iSNSServer

Specifies whether the IP address of a valid iSNS server from which the iPBridge will attempt iSCSI initiator discovery. Setting to 0.0.0.0 will disable iSNS server lookup.

Default: 0.0.0.0

Set syntax: set iSNSServer [xxx.xxx.xxx.xxx] Requires a SaveConfiguration command Get syntax: get iSNSServer

52 Interfaces: CLI

Image 61

ATTO Technology 2700C operation manual ISCSIWANIPAddress, ISNSLoginControl, ISNSServer

Contents

Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface options Maintenance commands CLI commands summary General use commandsDiagnostic commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commands Appendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmission Scsi Possible storage Configurations Atto iPBridge 2700R/D Installation instructions Front label side Back connector side Installation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management header Faceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP address Target management Default target nodeTarget names Map devices automatically Manually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodes Physical connections Initiator/Host to Network Mapping default vs. multiple target nodes Installation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & Date Snmp protocol Set up a Vlan Virtual Local Area Network Browser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target Management Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary steps Firmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logs Exhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devices Check host versions Check iPBridge product versions and update firmwareCheck components Checking the iSCSI Host Adapter or NIC Checking the LAN/WAN Checking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet ports Checking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet Explorer Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog box Exhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface Ready CLI Error Messages Command Defaults Example CLI commands summary Rmon Sntp Alternative interfaces CLI General use commands VerboseMode Username Maintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLog Diagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotify Ping IsReservedRouteDisplay SerialNumber SNMPTraps TemperatureTraceLog TraceLogFilter SerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPassword ISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable size Term Definition Appendix B Glossary FCC Standards Radio and Television Interference Appendix C Safety standards and compliances Vi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information