CLI commands summary | ATTO Technology 2700C guide

6.1.1 CLI commands summary

A summary of the Command Line Interface commands, their defaults, an example of how they might be used, and where you can find the specifics of the command. Commands which have no default values associated with them have a blank entry in that column of the table.

Command	Defaults	Example	Page
AccessControl		set accesscontrol default	53

AccessEntry		set accessentry default all	53

AutoMap		automap	53

BridgeModel		get bridgemodel	43

BridgeName	iPBridge	set bridgename Omega6	43

ClearEventLog		cleareventlog	43

ClearTraceLog		cleartracelog	43

Date		set date 03/03/2005	41

DisplayEventLog		displayeventlog	43

DisplayEventLogFilter	disabled	set displayeventlogfilter gen info enabled	43

DisplayTraceLog		displaytracelog	43

DisplayTraceLogFilter	disabled	set displaytracelogfilter all info enabled	43

DPMTU	1514	set dpmtu all 9014	49

DumpEventLog		dumpeventlog	44

DumpTraceLog		dumptracelog	44

EmailFromAddress		emailfromaddress 152.15.16.1	44

EmailNotify		emailnotify enabled	44

EmailNotifyAddress		emailnotifyaddress 152.16.1.1	44

EmailServerAddress		emailserveraddress 152.32.3.1	44

EthernetSpeed	auto	set ethernetspeed dp1 100	49

EventLog	enabled	set eventlog disabled	44

EventLogFilter	disabled	set eventlogfilter gen info enabled	44

Exit		exit	49

FCConnMode	loop	set fcconnmode 1 ptp	48

FCDataRate	auto	get fcdatarate 1	48

FCHard	disabled	set fchard enabled	48

FCHardAddress	fp1 = 3	set fchardaddress 1 4	48
	fp2 = 4

FCPortList		fcportlist	48

FCTargets		fctargets	48

35

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 44

ATTO Technology 2700C operation manual CLI commands summary, Command Defaults Example

Contents

Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Troubleshooting Atto ExpressNAV pagesUpdating firmware Alternative interface options Diagnostic commands CLI commands summary General use commandsMaintenance commands Serial port configuration commands Fibre Channel configuration commandsEthernet commands ISCSI commands Appendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 features, benefits Embedded software featuresAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmission Possible storage Configurations Scsi Atto iPBridge 2700R/D Installation instructions Back connector side Front label side Installation Atto iPBridge 2700R/D Atto iPBridge 2700C Ethernet interfaceFibre Channel interface Serial management header Faceplate side Power side Configuring the iPBridge Getting an IP address Click Launch Browser Default target node Target managementTarget names Map devices automatically Automatically configure multiple targets Manually configure multiple target nodesChap to control access different Chap Multiple target nodes Mapping default vs. multiple target nodes Physical connections Initiator/Host to Network Installation mapping Page Installation mapping Additional configurations Create a read only password or usernameSet the Real Time Clock Click Time & Date Set up a Vlan Virtual Local Area Network Snmp protocol Open an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Bridge Configuration Firmware UpdateAdvanced CLI Configuration Manual Target Management iSCSI Target Management Using Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary steps Firmware update Troubleshooting Inside out methodCheck the Host Event Log Check the event and trace logs Check for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplate Check components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NIC Performance Issues Checking the iSCSI OS driverChecking the Operating System Checking the iPBridge Ethernet ports Checking the Ethernet host adapter or NIC Checking applicationsChecking the host system Optimizing Atto ExpressNAV in Internet Explorer Alternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog box Exhibit 6.0-1 Start up messages Command conventions Symbol Indicates FCTargets commandCLI provides ASCII-based interface Ready CLI Error Messages CLI commands summary Command Defaults Example Rmon Sntp Alternative interfaces CLI General use commands Username VerboseMode Maintenance commands SpeedWriteDefault SNTPServerSpeedWrite TailEventLog Diagnostic commands DumpEventLog DumpTraceLogEmailFromAddress EmailNotify IsReserved PingRouteDisplay SerialNumber Temperature SNMPTrapsTraceLog TraceLogFilter SerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsername ISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Appendix a Cabling Fibre Channel connectionsEthernet connections Cable length Cable size Appendix B Glossary Term Definition Appendix C Safety standards and compliances FCC Standards Radio and Television Interference Vi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc