Atto ExpressNAV pages, Updating firmware | ATTO Technology 2700C

3.1 ATTO ExpressNAV pages

21

Status

Serial Port Configuration

Time & Date Configuration

Ethernet (Network) Port Configuration

SNMP

Fibre Channel Configuration iSCSI Configuration

Auto Target Management

Manual Target Management: iSCSI Target Management Bridge Configuration

Firmware Update Advanced CLI Configuration

To use the Advanced Configuration page Restart Firmware

Help

4 Updating firmware	23
Preliminary steps
Using ATTO ExpressNAV
Using FTP over GbE
5 Troubleshooting	25
Inside out method
Check the Host Event Log
Check the event and trace logs
Visually inspect LEDs
Check for problems on attached devices
Check host versions
Check iPBridge product versions and update firmware
Check components
Checking Fibre Channel devices
Checking the iPBridge FC ports
Checking iPBridge internal configuration
Checking iPBridge Ethernet ports
Checking the LAN/WAN
Checking the iSCSI Host Adapter or NIC
Checking the iSCSI OS driver
Checking the Operating System
Checking the Applications
Performance Issues
Checking Fibre Channel devices
Checking the iPBridge Ethernet ports
Checking the LAN/WAN
Checking the Ethernet host adapter or NIC
Checking applications
Checking the host system
Checking the Operating System
Optimizing ATTO ExpressNAV in Internet Explorer
6 Alternative interface options	31
Use the serial port or header
Use Telnet
6.1 CLI provides ASCII-based interface	33

CLI Error Messages

Image 5

ATTO Technology 2700C Atto ExpressNAV pages, Updating firmware, Troubleshooting, Alternative interface options

Contents

Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface options Diagnostic commands CLI commands summary General use commandsMaintenance commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commands Appendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmission Scsi Possible storage Configurations Atto iPBridge 2700R/D Installation instructions Front label side Back connector side Installation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management header Faceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP address Target management Default target nodeTarget names Map devices automatically Manually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodes Physical connections Initiator/Host to Network Mapping default vs. multiple target nodes Installation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & Date Snmp protocol Set up a Vlan Virtual Local Area Network Open an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target Management Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary steps Firmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logs Exhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devices Check components Check iPBridge product versions and update firmwareCheck host versions Checking the iSCSI Host Adapter or NIC Checking the LAN/WAN Checking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet ports Checking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet Explorer Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog box Exhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface Ready CLI Error Messages Command Defaults Example CLI commands summary Rmon Sntp Alternative interfaces CLI General use commands VerboseMode Username Maintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLog Diagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotify Ping IsReservedRouteDisplay SerialNumber SNMPTraps TemperatureTraceLog TraceLogFilter SerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPassword ISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable size Term Definition Appendix B Glossary FCC Standards Radio and Television Interference Appendix C Safety standards and compliances Vi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information