Manuals / ATTO Technology / Computer Equipment / Switch

ATTO Technology 2700C operation manual Updating firmware, Preliminary steps, Using Atto ExpressNAV

Models: 2700C

1 71

Download 71 pages 4.07 Kb

Page 32

4 Updating firmware

Several processors control the flow of data in the ATTO iPBridge 2700. The firmware to control these processors can easily be upgraded in the field using the ATTO ExpressNAV interface or the PUT command from an FTP connection. The ATTO ExpressNAV method is preferred.

Preliminary steps

1The iPBridge firmware is distributed as a compressed .zip file and can be obtained from the ATTO Technology, Inc. web site at www.attotech.com or from the CD included with your iPBridge.

2Uncompress the .zip file into an image file (.ima). Note the filename.

CAUTION

Before beginning this procedure, ensure that all I/O to the iPBridge has stopped.

Using ATTO ExpressNAV

1Connect to ExpressNAV (refer to ATTO ExpressNAV interface on page 19) and click on the Firmware page.

2Click Browse and locate the firmware you unzipped in the preliminary steps.

3Click Upload and wait until a success message is displayed.

4Click the Restart link.

5Click on Restart.

During this procedure, do not interrupt the flash process.

Do not power down the host or the iPBridge until the display returns the Ready prompt.

Interrupting the flash process will make your iPBridge inoperable and you will have to return it to ATTO Technology for repair.

Note

The recommended management tool for the iPBridge is ATTO ExpressNAV.

Using FTP over GbE

1Establish an FTP link to the bridge that is to be flashed.

2Use the PUT command to download the firmware you unzipped in the preliminary steps. For example

c:\bridge_firmware\I25i0300.ima

3Once the download is complete, cycle power on the iPBridge or use the FirmwareRestart CLI command.

23

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 32

ATTO Technology 2700C operation manual Updating firmware, Preliminary steps, Using Atto ExpressNAV, Using FTP over GbE

Contents

Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Troubleshooting Atto ExpressNAV pagesUpdating firmware Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Serial port configuration commands Fibre Channel configuration commandsEthernet commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 features, benefits Embedded software featuresAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Atto iPBridge 2700C Ethernet interfaceFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserDefault target node Target managementTarget names Map devices automaticallyAutomatically configure multiple targets Manually configure multiple target nodesChap to control access different Chap Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Additional configurations Create a read only password or usernameSet the Real Time Clock Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Bridge Configuration Firmware UpdateAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsFirmware update Troubleshooting Inside out methodCheck the Host Event Log Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NICPerformance Issues Checking the iSCSI OS driverChecking the Operating System Checking the iPBridge Ethernet portsChecking the Ethernet host adapter or NIC Checking applicationsChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerAlternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages Command conventions Symbol Indicates FCTargets commandCLI provides ASCII-based interface ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TailEventLogDiagnostic commands DumpEventLog DumpTraceLogEmailFromAddress EmailNotifyIsReserved PingRouteDisplay SerialNumberTemperature SNMPTrapsTraceLog TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Appendix a Cabling Fibre Channel connectionsEthernet connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc