Mapping default vs. multiple target nodes | ATTO Technology 2700C

Exhibit 2.2-1 Target node configurations

Physical connections Initiator/Host to Network

Network to iPBridge Ethernet port iPBridge SCSI port to SCSI device

Server 1

Ethernet
Network	Bridge SN	000123
	Bridge SN	000123
	IP Address: 10.0.3.0
	(1 IP Address for each Ethernet port)		SCSI device
			SCSI device

Server 2

Mapping: default vs. multiple target nodes

SCSI device configuration

Default Target node

Lun 0 Bridge SN 000123

Lun 1

Tape 0

Lun 2

Tape 1

Lun 3

Tape 2

Lun 4

Tape 3

Lun 5

Media Chgr

Node 0

iqn. 1995 - 12. com. attotech : ipbridge :sn- ipb 2700000123

SCSI device configuration

Multiple Target nodes

Lun 0 Bridge SN 000123

Lun 1

Tape 0

Lun 2

Tape 1

Lun 3

Media Chgr

Lun 0 Bridge SN 000123

Lun 1

Media Chgr

: Lun 2

Tape 2

Lun 3

Tape 3

Lun 0 Bridge SN 000123

Node 0

iqn. 1995-12. com. attotech: ipbridge:sn- ipb 2700000123-dev0

Node 1

iqn. 1995-12.com. attotech: ipbridge:sn- ipb2700000123-dev1

Default Node iqn1993-12.com.attotech ipbridgesn-ipb2700000123

13

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 22

ATTO Technology 2700C Physical connections Initiator/Host to Network, Mapping default vs. multiple target nodes

Contents

Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface options Maintenance commands CLI commands summary General use commandsDiagnostic commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commands Appendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmission Possible storage Configurations Scsi Atto iPBridge 2700R/D Installation instructions Back connector side Front label side Installation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management header Faceplate side Power side Configuring the iPBridge Getting an IP address Click Launch Browser Target names Default target nodeTarget management Map devices automatically Chap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodes Mapping default vs. multiple target nodes Physical connections Initiator/Host to Network Installation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & Date Set up a Vlan Virtual Local Area Network Snmp protocol Browser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target Management Updating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary steps Firmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logs Check for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplate Check host versions Check iPBridge product versions and update firmwareCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NIC Checking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet ports Checking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet Explorer Use Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog box Exhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command Ready CLI Error Messages CLI commands summary Command Defaults Example Rmon Sntp Alternative interfaces CLI General use commands Username VerboseMode Maintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLog Diagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotify RouteDisplay IsReservedPing SerialNumber TraceLog TemperatureSNMPTraps TraceLogFilter SerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsername ISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable size Appendix B Glossary Term Definition Appendix C Safety standards and compliances FCC Standards Radio and Television Interference Vi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc