ATTO Technology 2700C operation manual ReadOnlyPassword, ReadOnlyUsername

Ping

Ping will send an ICMP echo request to the specified host.

Immediate command: ping [DPn] mp1] [xxx.xxx.xxx.xxx] <count <size>>

ReadOnlyPassword

Specifies a read only password for all sessions: TCP/IP, FTP and ExpressNAV web-based interface. You will be prompted for the current password, to enter the new password, and to confirm the new password. Passwords are case sensitive, 0-32 characters with no spaces.An empty password can be configured by entering the Password confirmation prompts with no parameters. The command RestoreConfiguration default sets the password to its default value.

Default: Password

Set syntax: set ReadOnlyPassword

Requires a SaveConfiguration command

ReadOnlyUsername

Specifies a read only username for all TCP/IP, FTP and ExpressNAV web server sessions. Username is case insensitive, 1-32 characters with no spaces.

Default: user

Set syntax: set ReadOnlyUsername [username] Requires a SaveConfiguration command

Get syntax: get Username

Setting the history control entries take effect immediately, but changes must be saved to be persistent over a reboot.

Valid range for EthernetStat index: 1-3

Valid range for historyControl and EthernetHistory index: 1-6

Valid range for historyControl buckets requested: 1- 180

Valid range for historyControl interval: 1-3600 Default historyControl table (buckets and interval in hexadecimal)

Default: Refer to Exhibit 6.1.7-1

Set syntax: set RMON idx bucketsRequest interval [valid invalid]

Get syntax for entire table: get RMON [ethernetStat historyControl] <idx>

Get syntax for single index entry: get RMON ethernetHistory <idx sampleIdx>

Username

Specifies a username for all TCP/IP, FTP and ExpressNAV web server sessions. Username is case insensitive, 1-32 characters with no spaces.Changes to the Admin Level Username will require an Admin Level password.

Default: root

Set syntax: set Username [username]

Requires entering a password

Requires a SaveConfiguration command

Get syntax: get Username

RMON

RMON collects and stores Ethernet data on data ports at specified intervals. You can display the entire table requested, or a single entry based on the index (and sample index for the Ethernet History table).

Entries in the Ethernet History table are not valid when the Sample Index is 0.

VLAN

Creates up to eight Virtual LAN IDs for each Ethernet data port. Each VLAN ID is assigned a VLAN name of up to 64 characters. If no VLALN ID exists for a data port, VLAN is disabled for that port.

Set syntax: set VLAN [dp [n]] [[VLAN ID [VLAN Name] <delete> [all] [delete]]

Requires a SaveConfiguration command Get syntax: get VLAN [dp [n]]

Exhibit 6.1.7-1 Default history Control table (buckets and interval in hexadecimal) for the RMON CLI command.

Idx DataSrcBktReq BktGrant Interval Owner Status

====================================================================

001	43.6.1.2.1.2.2.1.1.1 00000032 00000032 0000001e monitor 00000004
002	43.6.1.2.1.2.2.1.1.1 00000032 00000032 00000708 monitor 00000004
003	43.6.1.2.1.2.2.1.1.2 00000032	00000032	0000001e	monitor 00000004
004	43.6.1.2.1.2.2.1.1.2 00000032	00000032	00000708	monitor 00000004
005	43.6.1.2.1.2.2.1.1.3 00000032	00000032	0000001e	monitor 00000004
006	43.6.1.2.1.2.2.1.1.3 00000032	00000032	00000708	monitor 00000004

50 Interfaces: CLI