Exhibit 6.0-1 Start up messages | ATTO Technology 2700C instruction

Exhibit 6.0-1 Start up messages.

ATTO iPBridge 2700

(c) 2002 - 2005 ATTO Technology, Incorporated.

Firmware version A76A release date Mar 31 2005, 14:40:12 Build A76A

255 Megabytes of RAM Installed.

4 GbE Data Port(s).
Bridge World Wide Name		= 20 00		00 10 86 30 00 38
Bridge Serial Number		= “iB2700L000000”
Bridge Name		= “iPBridge”
Internal Temperature =		30	C [0	- 70]
For help, type	HELP.
Active Configuration = ATTO
Mar 31 2005 14:40:12 A76A			Initialization Complete
STM41T0 RTC initialized			Test	Passed
FC Interface 1	PCI Config
FC Interface 1	Register Test			Passed
FC Interface 1	Reset Test			Passed
FC Interface 1	Initialization			Passed
FC Interface 2	PCI Config		Test	Passed
FC Interface 2	Register Test			Passed
FC Interface 2	Reset Test			Passed
FC Interface 2	Initialization			Passed

Initializing Port DP1..................................................

Initializing Port DP2..................................................

Initializing Port DP3..................................................

Initializing Port DP4..................................................

Initializing Port MP1............

GBE hardware Init done.Power-On Self-Test (POST) Completion Status: GOOD

Ready.

32 Installation: Alternative interfaces

Image 41

ATTO Technology 2700C operation manual Exhibit 6.0-1 Start up messages

Contents

Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface options Diagnostic commands CLI commands summary General use commandsMaintenance commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commands Appendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmission Scsi Possible storage Configurations Atto iPBridge 2700R/D Installation instructions Front label side Back connector side Installation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management header Faceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP address Target management Default target nodeTarget names Map devices automatically Manually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodes Physical connections Initiator/Host to Network Mapping default vs. multiple target nodes Installation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & Date Snmp protocol Set up a Vlan Virtual Local Area Network Open an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target Management Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary steps Firmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logs Exhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devices Check components Check iPBridge product versions and update firmwareCheck host versions Checking the iSCSI Host Adapter or NIC Checking the LAN/WAN Checking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet ports Checking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet Explorer Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog box Exhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface Ready CLI Error Messages Command Defaults Example CLI commands summary Rmon Sntp Alternative interfaces CLI General use commands VerboseMode Username Maintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLog Diagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotify Ping IsReservedRouteDisplay SerialNumber SNMPTraps TemperatureTraceLog TraceLogFilter SerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPassword ISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable size Term Definition Appendix B Glossary FCC Standards Radio and Television Interference Appendix C Safety standards and compliances Vi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information