Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 6H122-16 Broadcast Suppression Screen, PORT # Read-only, Total RX Read-Only

Models: 6H122-16

1 158

Download 158 pages 26.97 Kb

Page 123

				Broadcast Suppression Screen

	Event Message Line
			6C105 LOCAL MANAGEMENT
				Broadcast Suppression
	Module Type: 6H122-16				Firmware Revision: XX.XX.XX
	Slot Number: X				BOOTPROM Revision: XX.XX.XX
	PORT #	Total RX	Peak Rate	Time Since Peak	Threshold	Reset Peak
	1	12345678910	150000	999:23:59	150000		[NO]
	2	12345678910	150000	999:23:59	150000		[NO]
	3	12345678910	150000	999:23:59	150000		[NO]
	4	12345678910	150000	999:23:59	150000		[NO]
	5	12345678910	150000	999:23:59	150000		[NO]
	6	12345678910	150000	999:23:59	150000		[NO]
	7	12345678910	150000	999:23:59	150000		[NO]
	8	12345678910	150000	999:23:59	150000		[NO]
	9	12345678910	150000	999:23:59	150000		[NO]
	10	12345678910	150000	999:23:59	150000		[NO]
	11	12345678910	150000	999:23:59	150000		[NO]
	12	12345678910	150000	999:23:59	150000		[NO]
		SAVE		[13-16]	EXIT
		SAVE		[13-16]	EXIT		RETURN

						2361_25

Figure 5-33 Broadcast Suppression Screen

The following explains each ﬁeld of the Broadcast Statistics screen:

PORT # (Read-only)

Identiﬁes the number of the port.

Total RX (Read-Only)

Displays the total number of broadcast frames received.

Peak Rate (Read-Only)

Displays the number of broadcast frames received per second.

6H122-16 User’s Guide

5-83

Image 123

Cabletron Systems 6H122-16 Broadcast Suppression Screen, PORT # Read-only, Total RX Read-Only, Peak Rate Read-Only, 5-83

Contents

1X 2X 3X 4X 5X 6X 7X 8X 9X 10X 11X 12X 13X 14X 15X 16X 6H122-16 SmartSwitch 6000 Interface Module User’s Guide6H122-16 RESET 9032361-03Page Only qualiﬁed personnel should install the 6H122-16 FCC NOTICE6H122-16 User’s Guide 6H122-16 User’s Guide INDUSTRY CANADA NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT6H122-16 User’s Guide EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTS6H122-16 User’s Guide SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS LASER RADIATION AND CONNECTORSManufacturer’s Name Cabletron Systems, Inc DECLARATION OF CONFORMITY6H122-16 User’s Guide Application of Council Directives 89/336/EEC 73/23/EEC6H122-16 User’s Guide CHAPTER CONTENTSINSTALLATION TROUBLESHOOTINGviii ContentsCHAPTER LOCAL MANAGEMENT6H122-16 User’s Guide ContentsAPPENDIX A ContentsSPECIFICATIONS MODE SWITCH BANK SETTINGS1.1 USING THIS GUIDE CHAPTER INTRODUCTION1.2 STRUCTURE OF THIS GUIDE Chapter 1 Introduction 1.3 OVERVIEW1.3.1 Connectivity 1.3.2 Management6H122-16 User’s Guide Reset Button COM Port System LED Port Status LEDs Network PortsRESET Overview1.3.6 Remote Monitoring 1.3.4 Switching Options1.3.5 Full Duplex Switched Ethernet 1.3.3 Distributed Chassis Management1.3.8 Runtime IP Address Discovery 1.3.7 SmartTrunk1.3.9 Port Redirect Function 1.3.10 Auto-Negotiation1.3.11 Broadcast Suppression 1.3.13 LANVIEW Diagnostic LEDs 1.3.12 Standards Compatibility1.3.14 Year 2000 Compliant 6H122-16 User’s Guide 1.4 DOCUMENT CONVENTIONSThe following conventions are used throughout this document Chapter 1 Introduction1.5 GETTING HELP Cabletron Systems Cabling Guide 1.6 RELATED MANUALSThe following manuals may help to set up, control, and manage the 6H122-162.1 SmartTrunk CHAPTER NETWORK REQUIREMENTS2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORKChapter 2 Network Requirements 3.1 UNPACKING THE 6H122-16 CHAPTER INSTALLATIONor components 3.2 INSTALLING THE 6H122-16 INTO THE 6C105 CHASSISengages the backplane connectors 6H122-16 User’s Guide Chapter 3 InstallationFigure 3-1 Installing an Interface Module Connector3.3 CONNECTING TO THE NETWORK Figure 3-2 6H122-16 Twisted Pair Connection RX Receive LED Columnmust share a common SmartSwitch RJ45 PortFigure 3-3 Cable Pinouts - RJ45 Crossover Cable Figure 3-4 Cable Pinouts - RJ45 Straight-Through Cable3.4 COMPLETING THE INSTALLATION Chapter 3 Installation6H122-16 User’s Guide 4.1 USING LANVIEW CHAPTER TROUBLESHOOTINGFigure 4-1 LANVIEW LEDs Chapter 4 TroubleshootingRESET 6H122-16 User’s GuideColor Using LANVIEW6H122-16 User’s Guide Table 4-1 LANVIEW LEDsColor Chapter 4 Troubleshooting6H122-16 User’s Guide Table 4-1 LANVIEW LEDs ContinuedProblem 4.2 TROUBLESHOOTING CHECKLISTTroubleshooting Checklist Table 4-3 Troubleshooting Checklist6H122-16 User’s Guide Chapter 4 TroubleshootingTable 4-3 Troubleshooting Checklist Continued Problem6H122-16 4.3 USING THE RESET BUTTON6H122-16 User’s Guide Chapter 4 Troubleshooting5.1 OVERVIEW CHAPTER LOCAL MANAGEMENTTable 5-1 Keyboard Conventions 5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONSChapter 5 Local Management 6H122-16 User’s Guide5.3.1 Console Cable Connection 5.3 MANAGEMENT TERMINAL SETUP6H122-16 User’s Guide UTP Cable with RJ45 Connectors RJ45-to-DB9 PC Adapter to PC PC6H122-16 RESET Chapter 5 Local ManagementDisplay Setup Menu 5.3.2 Management Terminal Setup ParametersManagement Terminal Setup Table 5-2 VT Terminal Setup5.3.3 Telnet Connections 5.3.4 Connecting an Uninterruptible Power SupplyRESET Management Terminal SetupFigure 5-2 Uninterruptible Power Supply UPS Connection RESETFigure 5-3 The Local Management Password Screen 5.4 ACCESSING LOCAL MANAGEMENT5.4.1 Navigating Local Management Screens 5-10 Figure 5-4 802.1D Switching Mode, LM Screen HierarchyFigure 5-5 802.1Q Switching Mode, LM Screen Hierarchy Chapter 5 Local Management5.4.3 Exiting Local Management Screens 5.4.2 Selecting Local Management Menu Screen Items5. Press ENTER. The Password screen displays and the session ends 5.5 THE MAIN MENU SCREEN CHASSISMODULES CHASSIS CONFIGURATION 5.6 CHASSIS MENU SCREENPORT REDIRECT FUNCTION SNMP COMMUNITY NAMESSNMP TRAPS CHASSIS ENVIRONMENTAL5.7 CHASSIS CONFIGURATION SCREEN Screen Refresh Time Modiﬁable Subnet Mask ModiﬁableChassis Date Modiﬁable Chassis Time Modiﬁable5.7.1 Setting the IP Address 5.7.3 Setting the Chassis Date 5.7.2 Setting the Subnet Mask5.7.4 Setting the Chassis Time 5.7.5 Entering a New Screen Refresh Time 5.7.6 Setting the Screen Lockout Time5.7.7 Setting the Operational Mode 5-23 If the 6H122-16 has been set to 802.1Q SWITCHING, refer to your Port Based VLAN User’s Guide to conﬁgure the devices for this type of operationChassis Conﬁguration Screen 6H122-16 User’s GuideFigure 5-11 SNMP Community Names Screen 5.8 SNMP COMMUNITY NAMES SCREEN5.8.1 Establishing Community Names 5.9 SNMP TRAPS SCREEN The following explains each ﬁeld of the SNMP Traps screen 5.9.1 Conﬁguring the Trap Table 5.10 CHASSIS ENVIRONMENTAL SCREEN Chassis Power Redundancy Read-OnlyPower Supply #X Status Read-Only Chassis Fan Status Read-Only 5.11 PORT REDIRECT FUNCTION SCREENDisplays which modules are currently set as source modules 5.11.1 Changing Source and Destination Ports 3. Use the arrow keys to highlight the Source Port field SLOT # Selectable 5.12 MODULE SELECTION SCREEN5.12.1 Selecting a Module MODULE CONFIGURATION 5.13 MODULE MENU SCREEN5.14 MODULE CONFIGURATION MENU SCREEN MODULE STATISTICSNETWORK TOOLS Figure 5-17 Module Conﬁguration Menu Screen GENERAL CONFIGURATIONThe SmartTrunk Conﬁguration screen allows the user to logically group interfaces together to create a greater bandwidth uplink. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information 5.15 GENERAL CONFIGURATION SCREEN Page Page Section 5.15.10 describes how to set the Management Mode IP Fragmentation Toggle 5.15.1 Setting the IP AddressFigure 5-19 Conﬁguration Warning Screen 5.15.2 Setting the Subnet Mask5.15.3 Setting the Default Gateway 5.15.5 Setting the Module Date 5.15.4 Setting the TFTP Gateway IP Address5.15.6 Setting the Module Time 5.15.7 Entering a New Screen Refresh Time 5.15.8 Setting the Screen Lockout Time5-50 5.15.9 Setting the Operational Mode802.1D SWITCHING, 802.1Q SWITCHING, or SECURE FAST VLAN Chapter 5 Local Management5-51 Upon saving the new operational mode, the module will rebootGeneral Conﬁguration Screen 6H122-16 User’s Guide5.15.10 Setting the Management Mode 6H122-16 User’s Guide 5.15.11 Conﬁguring the COM PortSection 5.15.1 , Setting the IP Address . Read this entire General Conﬁguration Screen3. Use the arrow keys to highlight YES. Press ENTER 5.15.12 Changing the Com Port Application 5.15.13 Clearing NVRAM 5.16 SNMP COMMUNITY NAMES SCREEN 5.15.14 Enabling/Disabling IP Fragmentationaccess to security-protected ﬁelds of read-write access to the 6H122-16 MIB objects, excludingFigure 5-25 SNMP Community Names Screen 5.16.1 Establishing Community Names Figure 5-26 SNMP Traps Screen 5.17 SNMP TRAPS SCREEN5.17.1 Conﬁguring the Trap Table Figure 5-27 Switch Conﬁguration Screen 5.18 SWITCH CONFIGURATION SCREENThe following describe each ﬁeld of the Switch Conﬁguration screen 5.18.1 Setting the STA 5.18.3 Setting Enabling or Disabling the Port Status 5.18.2 Setting the Age Time6H122-16 User’s Guide 5.19 ETHERNET INTERFACE CONFIGURATIONChapter 5 Local Management 5-66Displays the number of the front panel interface 5.19.1 Conﬁguring the Ports 5.19.2 Setting the Operational Mode5.19.4 Setting the Flow Control Admin Status 5.19.3 Setting the Advertised Ability5.20 MODULE SPECIFIC CONFIGURATION MENU SCREEN Figure 5-29 Module Speciﬁc Conﬁguration Screen SYSTEM RESOURCES5.21 SYSTEM RESOURCES SCREEN The following brieﬂy explains each ﬁeld of the System Resources screen 5.22 FLASH DOWNLOAD SCREEN 5.21.1 Setting the Reset Peak UtilizationDownload Method Selectable The following brieﬂy explains each ﬁeld of the Flash Download screen5.22.1 Image File Download Using TFTP 5.22.2 Image File Download Using RUNTIME 5.22.3 Image File Download Using BootP 5.23 PORT REDIRECT FUNCTION SCREEN Figure 5-32 Port Redirect Function Screen 5.23.1 Changing Source and Destination Ports 5.24 BROADCAST SUPPRESSION SCREEN Peak Rate Read-Only Broadcast Suppression ScreenPORT # Read-only Total RX Read-OnlyTime Since Peak Read-Only 5.24.1 Setting the Threshold5.24.2 Setting the Reset Peak Switch Reset Peak Toggle5-85 5.25 MODULE STATISTICS MENU SCREENModule Statistics Menu Screen 6H122-16 User’s GuideThe Module Statistics Menu screen displays the following menu items Figure 5-35 Switch Statistics Screen 5.26 SWITCH STATISTICS SCREEN5.26.1 Using the Clear Counters Command Interface Read-only 5.27 INTERFACE STATISTICS SCREENInUnicast Read-only InErrors Read-onlyName Read-only InOctets Read-onlyOutDiscards Read-only OutErrors Read-onlyAdmin Status Read-only OutNonUnicast Read-only5.27.1 Displaying Interface Statistics 5.27.2 Using the Clear Counters CommandRMON Index Read-only 5.28 RMON STATISTICS SCREENThis ﬁeld displays the name of the entity that conﬁgured this entry The total number of undersized frames with a bad CRC 256 - 511 Octets Read-only Index nn CommandCLEAR COUNTERS Command 128 - 255 Octets Read-only5.28.1 Displaying RMON Statistics 5.28.2 Using the Clear Counters Command5.29 NETWORK TOOLS Type help at the prompt to list all the commands that areUse lower case when entering commands in Network Tools Options commandSyntax DescriptionOptions 5.29.1 Built-in Commandsarp options SyntaxOptions ExampleSyntax DescriptionExample SyntaxDescription OptionsOptions ExampleSyntax DescriptionExample SyntaxresetNot Applicable OptionsDescription not reached, the command displays all next-hopExample SyntaxDescription OptionsExample SyntaxDescription 5.29.2 Special Commandslinktrap SyntaxChapter 5 Local Management 5-1086H122-16 User’s Guide A.3 ENVIRONMENTAL REQUIREMENTS APPENDIX A SPECIFICATIONSA.1 DEVICE SPECIFICATIONS A.2 PHYSICAL PROPERTIESA.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTSREGULATORY COMPLIANCE APPENDIX B MODE SWITCH BANK SETTINGS B.2 SETTING THE MODE SWITCHB.1 REQUIRED TOOLS Switch deﬁnitions and positions are as follows Switch 7 - Clear NVRAM. Changing the position of this switch resets NVRAM on the next power up. ALL user entered parameters, such as IP addresses, subnet masks, SNMP traps, and switching functions are restored to their factory default settings 6H122-16 User’s Guide Appendix B Mode Switch Bank SettingsIndex-1 INDEXNumerics 6H122-16 User’s GuidePage Index 6H122-16 User’s GuideIndex-3 Index Index-46H122-16 User’s Guide