Manuals / Emerson / Home Audio / Satellite Radio

Emerson IFT9701 instruction manual Getting Started, Chapter, 2.1Safety, reliability, accessibility

Models: IFT9701

1 90

Download 90 pages 24.24 Kb

Page 13

Getting Started

Chapter 2

Getting Started

2.1Safety, reliability, accessibility

WARNING

Improper installation in a hazardous area could cause an explosion.

Install the transmitter in an environment that is compatible with the hazardous area specified on the approvals tag.

•For intrinsically safe sensor installations, use this document with Micro Motion ATEX, CSA, or UL installation instructions.

•For hazardous area installations in Europe, refer to standard EN 60079-14 if national standards do not apply.

2.1.1Hazardous area

If you plan to mount the transmitter in a hazardous area, ensure that your equipment and installation meet the hazardous area requirements. For more information about hazardous area classifications, see Section A.8. See Figure 2-1 for the location of the approvals tag on your transmitter.

Before You Begin

Getting Started

Mounting the Remote Transmitter

Power Supply and Output Wiring

Model IFT9701 Transmitter Instruction Manual

5

Image 13

Emerson IFT9701 instruction manual Getting Started, Chapter, 2.1Safety, reliability, accessibility, 2.1.1Hazardous area

Contents

Model IFT9701 Transmitter with Optional Display Micro MotionMicro MotionTM P/N 3100572, Rev. E MarchPage Model IFT9701 Transmitter with Optional Display Micro MotionPage Contents Chapter 6 Configuration with a HART Communicator Chapter 8 TroubleshootingChapter 7 Configuration with ProLink II Software Contents continuedPage Page Before You Begin Chapter1.2Safety 1.1About this manual1.4Definitions 1.3European installations1.5Flowmeter components Before You Begin continuedSensor wiring Field wiringPower Supply and Output Wiring Figure 1-2Remotely mounted IFT9701 transmitterPage 2.1Safety, reliability, accessibility Getting StartedChapter 2.1.1Hazardous areaFigure 2-1Location of approvals tag 2.1.3Temperature, humidity, and vibration2.1.2Orientation and mounting 2.1.4Visibility of tags Power Supply and Output Wiring2.2Transmitters approved for ATEX Zone Explosion hazardFigure 2-2Compartment tags and lockout device 2.3Jumper settingsFigure 2-3Jumper location and settings 2.3.2Fault output levelsDefault settings Optional settings1.Screw the cover back onto the housing Chapter Remotely Mounting the Transmitter3.1Overview 3.2Choosing the proper locationRemotely Mounting the Transmitter continued Circuit board compartment 3.4.1Cable types 3.4Connecting the transmitter to the sensorFigure 3-4Jacketed cable Low operating temperature limit Table 3-1Temperature ranges for jacket materialHigh operating temperature limit Installation requirementsInstall drip legs in cable or conduit 3.4.4Wiring connections to sensor3.4.2Guidelines for conduit 3.4.3Guidelines for cable glandPower Supply and Output Wiring Wire colorFigure 3-7Cable connections to sensors Table 3-3Sensor terminal designationsRemotely Mounting the Transmitter continued Sensor wiring terminals Sensor wiring compartment4.2Wiring guidelines Power Supply and Output WiringChapter 4.1OverviewFigure 4-1Power supply wiring terminals 4.3Connect power supply wiringPower Supply and Output Wiring continued 4.4Connect output wiring Table 4-1Wire guidelines for DC power supplyFigure 4-2Output wiring terminals Power Supply and Output Wiring continuedFigure 4-3Milliamp output performance 4.4.1Milliamp outputNote For optimum HART communication, make Figure 4-4Typical HART network wiringFigure 4-5HART Communicator connections 4.4.4Pulse output Pulse counter with pull-upto internal power Input 2Do not connect shields at this end Page 5.2Customer service Flowmeter Startup5.3Startup procedures Chapter5.4Initialization 5.4.1Diagnostic LED5.4.2Optional display 5.4.3Startup modeFigure 5-1Location of LED, zero button, and LCD 5.5.1Zeroing procedure5.5Flowmeter zeroing 5.5.2Diagnosing zero failure Configuration with ProLink Troubleshooting Configuration with Communicator5.7Process measurement Flowmeter Startup continuedPage 6.1Configuration overview Configuration with a HART CommunicatorChapter 6.2.1HART tag 6.2Configuration parameters6.2.2Measurement units a. Whenever the display below appears, press F4 OK 6.2.4Damping 6.2.3Flow cutoff6.2.5 Flow direction 6.2.7Pulse output scaling 6.2.6Range values for milliamp output6.3.1Auto zero 6.3Calibration proceduresDiagnosing zeroing failure 6.3.2Flow calibration procedureTo calculate the flow calibration factor 6.4Characterization 7.1Configuration overview Configuration with ProLink II SoftwareChapter Figure 7-1Configuration window - Device panel 7.2Configuration parameters7.2.1HART tag 7.2.2Process variable measurement Figure 7-2Configuration window - Flow panelThe pulse output goes to 0 Hz Page 7.2.3Output configuration 7.3Calibration procedures Figure 7-4Configuration window - Frequency panel7.3.1Auto zero To perform the auto zero procedure Figure 7-5Flow Calibration dialog box 7.3.2Flow calibration procedureDiagnosing zeroing failure Figure 7-6Totalizer Control window 7.4Characterization Configuration with ProLink II Software continued Figure 7-7Configuration window - Density panel8.1Customer service Troubleshooting8.3Transmitter diagnostic tools 8.3.1Diagnostic LEDTroubleshooting continued 8.3.3Fault outputs8.3.2Optional LCD Table 8-1Normal conditions indicated by LEDTable 8-2Conditions indicated by optional LCD 8.4Power supply8.5Wiring Figure 8-2Power supply connections8.6Over range and sensor failure conditions Table 8-3Sensor terminal designations8.7Slug flow 8.8Transmitter failure 8.9Digital diagnostic messagesPage Appendix A IFT9701 SpecificationsA.1 Performance specifications A.2 Functional specificationsA.2.7 Output testing Current source A.2.6 Fault indicationA.2.8 Power supply options 85 to 250 VAC A.2.2 Local display optionalSee Process fluid vs. ambient temperature, below A.3 Environmental limits A.3.1 TemperatureA.3.2 Process fluid temperature limits See Process fluid vs. ambient temperature, belowA.3.3 Humidity limits IFT9701 Specifications continued5 to 95% non-condensing A.3.4 Vibration limitsA.7 Shipping weight A.6 Ambient temperature effect on milliamp outputA.5 Environmental effects A.8 Hazardous area classificationsPage HART Communicator Menu Trees Appendix BSpecifications HART Menu TreesOnline Menu HART Communicator Menu Trees continuedSee previous page Appendix C Installing the Optional DisplayBack of Retaining clip display Installing the Optional Display continuedReturn Policy Appendix DD.1 General guidelines D.2 New and unused equipmentPage Index Page Page Page Page Micro MotionTM 3100572Micro Motion Inc. USA Worldwide Headquarters