Manuals / Emerson / Home Audio / Satellite Radio

Emerson IFT9701 instruction manual Circuit board compartment

Models: IFT9701

1 90

Download 90 pages 24.24 Kb

Page 21

Manual background

Remotely Mounting the Transmitter continued

Figure 3-2 Mounting the transmitter to a wall or other surface

Circuit board compartment

User access not normally required

Area approvals tag

Field wiring compartment

Sensor wiring compartment

4X M8 bolt

4X lock washer

4X flat washer

To rotate transmitter: remove, then re-install to 12 ft-lb (16 N-m) torque

4X 5/16 (M8) bolt

User-supplied

Figure 3-3 Mounting the transmitter to an instrument pole

Area approvals tag

Field wiring compartment

Sensor wiring compartment

4X 5/16 (M8) bolt

User-supplied

4X M8 bolt

4X lock washer

4X flat washer

To rotate transmitter: remove, then re-install to 12 ft-lb (16 N-m) torque

Circuit board compartment

User access not normally required

2X 5/16-inch (M8) U-bolt for 2-inch pipe

User-supplied

Before You Begin

Getting Started

Mounting the Remote Transmitter

Power Supply and Output Wiring

Model IFT9701 Transmitter Instruction Manual

13

Image 21

Emerson IFT9701 instruction manual Circuit board compartment

Contents

Model IFT9701 Transmitter with Optional Display Micro MotionMicro MotionTM P/N 3100572, Rev. E MarchPage Model IFT9701 Transmitter with Optional Display Micro MotionPage Contents Chapter 6 Configuration with a HART Communicator Chapter 8 TroubleshootingChapter 7 Configuration with ProLink II Software Contents continuedPage Page Before You Begin Chapter1.2Safety 1.1About this manual1.4Definitions 1.3European installations1.5Flowmeter components Before You Begin continuedSensor wiring Field wiringPower Supply and Output Wiring Figure 1-2Remotely mounted IFT9701 transmitterPage 2.1Safety, reliability, accessibility Getting StartedChapter 2.1.1Hazardous area2.1.3Temperature, humidity, and vibration Figure 2-1Location of approvals tag2.1.2Orientation and mounting 2.1.4Visibility of tags Power Supply and Output Wiring2.2Transmitters approved for ATEX Zone Explosion hazardFigure 2-2Compartment tags and lockout device 2.3Jumper settingsFigure 2-3Jumper location and settings 2.3.2Fault output levelsDefault settings Optional settings1.Screw the cover back onto the housing Chapter Remotely Mounting the Transmitter3.1Overview 3.2Choosing the proper locationRemotely Mounting the Transmitter continued Circuit board compartment 3.4Connecting the transmitter to the sensor 3.4.1Cable typesFigure 3-4Jacketed cable Low operating temperature limit Table 3-1Temperature ranges for jacket materialHigh operating temperature limit Installation requirementsInstall drip legs in cable or conduit 3.4.4Wiring connections to sensor3.4.2Guidelines for conduit 3.4.3Guidelines for cable glandPower Supply and Output Wiring Wire colorFigure 3-7Cable connections to sensors Table 3-3Sensor terminal designationsRemotely Mounting the Transmitter continued Sensor wiring terminals Sensor wiring compartment4.2Wiring guidelines Power Supply and Output WiringChapter 4.1Overview4.3Connect power supply wiring Figure 4-1Power supply wiring terminalsPower Supply and Output Wiring continued 4.4Connect output wiring Table 4-1Wire guidelines for DC power supplyFigure 4-2Output wiring terminals Power Supply and Output Wiring continuedFigure 4-3Milliamp output performance 4.4.1Milliamp outputNote For optimum HART communication, make Figure 4-4Typical HART network wiringFigure 4-5HART Communicator connections 4.4.4Pulse output Pulse counter with pull-upto internal power Input 2Do not connect shields at this end Page 5.2Customer service Flowmeter Startup5.3Startup procedures Chapter5.4Initialization 5.4.1Diagnostic LED5.4.2Optional display 5.4.3Startup mode5.5.1Zeroing procedure Figure 5-1Location of LED, zero button, and LCD5.5Flowmeter zeroing 5.5.2Diagnosing zero failure Configuration with ProLink Troubleshooting Configuration with Communicator5.7Process measurement Flowmeter Startup continuedPage Configuration with a HART Communicator 6.1Configuration overviewChapter 6.2Configuration parameters 6.2.1HART tag6.2.2Measurement units a. Whenever the display below appears, press F4 OK 6.2.4Damping 6.2.3Flow cutoff6.2.5 Flow direction 6.2.7Pulse output scaling 6.2.6Range values for milliamp output6.3.1Auto zero 6.3Calibration proceduresDiagnosing zeroing failure 6.3.2Flow calibration procedureTo calculate the flow calibration factor 6.4Characterization Configuration with ProLink II Software 7.1Configuration overviewChapter 7.2Configuration parameters Figure 7-1Configuration window - Device panel7.2.1HART tag 7.2.2Process variable measurement Figure 7-2Configuration window - Flow panelThe pulse output goes to 0 Hz Page 7.2.3Output configuration Figure 7-4Configuration window - Frequency panel 7.3Calibration procedures7.3.1Auto zero To perform the auto zero procedure 7.3.2Flow calibration procedure Figure 7-5Flow Calibration dialog boxDiagnosing zeroing failure Figure 7-6Totalizer Control window 7.4Characterization Configuration with ProLink II Software continued Figure 7-7Configuration window - Density panel8.1Customer service Troubleshooting8.3Transmitter diagnostic tools 8.3.1Diagnostic LEDTroubleshooting continued 8.3.3Fault outputs8.3.2Optional LCD Table 8-1Normal conditions indicated by LEDTable 8-2Conditions indicated by optional LCD 8.4Power supply8.5Wiring Figure 8-2Power supply connections8.6Over range and sensor failure conditions Table 8-3Sensor terminal designations8.7Slug flow 8.8Transmitter failure 8.9Digital diagnostic messagesPage Appendix A IFT9701 SpecificationsA.1 Performance specifications A.2 Functional specificationsA.2.7 Output testing Current source A.2.6 Fault indicationA.2.8 Power supply options 85 to 250 VAC A.2.2 Local display optionalSee Process fluid vs. ambient temperature, below A.3 Environmental limits A.3.1 TemperatureA.3.2 Process fluid temperature limits See Process fluid vs. ambient temperature, belowA.3.3 Humidity limits IFT9701 Specifications continued5 to 95% non-condensing A.3.4 Vibration limitsA.7 Shipping weight A.6 Ambient temperature effect on milliamp outputA.5 Environmental effects A.8 Hazardous area classificationsPage HART Communicator Menu Trees Appendix BSpecifications HART Menu TreesHART Communicator Menu Trees continued Online MenuSee previous page Appendix C Installing the Optional DisplayBack of Retaining clip display Installing the Optional Display continuedReturn Policy Appendix DD.1 General guidelines D.2 New and unused equipmentPage Index Page Page Page Page Micro MotionTM 3100572Micro Motion Inc. USA Worldwide Headquarters