Everpure 2001 SETTING TOP PAUSE, SETTING THE DEFAULT

SUPREMA 2001 - OPERATION & SERVICE MANUAL

SETTING THE DEFAULT

1.To program the default settings, press the "UP" button on the hidden menu scroll buttons and scroll until the following message appears,

SET DEFAULT

PRESS <START>

a)Press the "START" button to enter the set mode.

b)The LED's that correspond to the current default setting will now be illuminated.

c)To change the default, press the buttons on the selection panel for the new default settings. The LED's that are illuminated will now become the new default settings.

d)In no default is set, the LED’s on the selection panel will light and scroll until the user selects one. This applies for the products, strengths, and cup sizes, therefore three selections will be required by the user.

e)To exit the "SET DEFAULT" mode and proceed to the next setting, press the "UP" or "DOWN" scroll buttons.

SETTING TOP PAUSE

!Note:

The minimum setting for the “TOP PAUSE” is 2.0 seconds.

The “TOP PAUSE” occurs when the brewer is at top dead center, and is before the regular pause. When the piston reaches top dead center in the cylinder, the brewer will pause for the amount of time set in this menu, to allow the coffee and water to steep (mix together). The higher the "TOP PAUSE" is set to, the stronger the cup of coffee that is brewed by the equipment.

1.To set the "TOP PAUSE" setting, press the "UP" button on the hidden menu scroll buttons and scroll until the following message appears,

SET TOP PAUSE

PRESS <START>

a)Press the "START" button to enter the set mode.

b)At this point, select the cup size by pressing the appropriate buttons on the selection panel. The "TOP PAUSE" setting displayed will correspond to the cup size that is illuminated.

c)Using the hidden setting adjustment buttons, increase or decrease the timing for the "TOP PAUSE".

d)To exit the "SET TOP PAUSE" mode and proceed to the next setting, press the "UP" or "DOWN" scroll buttons.

Page 20 of 60

July 6, 2001

Suprema 2001 - Operation & Service

Contents

Software Version TABLE OF CONTENTS DIFFERENCES BETWEEN THE VISTA 3 AND THE SUPREMA OVERVIEW OF SUPREMA COMPONENTS SELECTION PANELS & INTERIOR DOOR PANELS UNPACKING & SETTING UP THE EQUIPMENT REMOVING SHIPPING MATERIALS WARNING: CONNECTIONS AND ADJUSTMENTS APPLYING THE FASCIA APPLYING THE INNER DOOR DECALS INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL WATER CONNECTION INSTALLATION AT AN ACCOUNT CONNECTING TO A WATER SUPPLY RUNNING COPPER TUBING FINISHING TOUCHES PROGRAMMING THE EQUIPMENT COIN DISPENSE TOTAL PER SELECTION COUNTER TOTAL COUNTER RESET "TOTAL COUNTER RESET" ACCESS CODE SET-UPMODE & ACCESS CODE PRODUCT ON/OFF SETTING PRODUCTS SETTING WATER SETTING PRICES ENABLING SWITCHES CANCELING INDIVIDUAL SELECTIONS SETTING THE DEFAULT SETTING TOP PAUSE SETTING BOTTOM PAUSE SETTING THE MAXIMUM NUMBER OF CUPS PER CARAFE SETTING THE FREQUENCY OF MESSAGES SERVICE COUNTER SETTING BOTTOM PAUSE DELAY CANCELING MESSAGES (MESSAGES ON, OFF or "ACTIVE") FREE VEND KEY SWITCH SET-UP SETTING THE “EMPTY GROUNDS CONTAINER” MESSAGE SETTING NUMBER OF CHOCOLATE PUMP CYCLES SETTING THE DOUBLE-CUP SETTING THE TEMPERATURE PROGRAMMING A CUSTOM MESSAGE SETTING LANGUAGE SETTING THE WATER LEVEL PROBE SETTING THE POST-MIX LOCKING THE COUNTERS SETTING THE FORCE VEND FEATURE OPERATION INFORMATION PRIMING THE CHOCOLATE PUMP SYSTEM STATUS INDICATORS GENERAL INFORMATION RINSE CYCLES BREWER RINSE CYCLE DOWNLOADING SOFTWARE AND TRANFERRING SETTINGS Page TRANSFERRING SETTINGS FROM ONE SUPREMA TO ANOTHER STEP 1 - TRANSFERRING SETTINGS TO THE DATA LINK DEVICE STEP 2 - TRANSFERRING SETTINGS FROM THE DATA LINK DEVICE TO A SUPREMA STEP 3 - TRANSFERRING CUSTOM MESSAGES TO A SUPREMA INDICATOR MESSAGES Page CORRECTIVE ACTION REPLACING MAJOR COMPONENTS REMOVING THE BREWER MOTOR INSTALLING THE BREWER MOTOR REMOVING THE INLET VALVE INSTALLING THE INLET VALVE REMOVING THE OUTLET VALVES CAUTION: INSTALLING THE OUTLET VALVES REMOVING THE WATER TANK ASSEMBLY INSTALLING THE WATER TANK REMOVING THE WATER TANK LID ASSEMBLY INSTALLING THE WATER TANK LID ASSEMBLY REMOVING THE HEATER ELEMENT INSTALLING THE HEATER ELEMENT REMOVING THE DRAIN VALVE INSTALLING THE DRAIN VALVE REMOVING THE INGREDIENT DISPENSER INSTALLING THE INGREDIENT DISPENSER REMOVING AN INGREDIENT DISPENSER MOTOR INSTALLING AN INGREDIENT DISPENSER MOTOR REMOVING THE SUPREMA FRONT BOARD INSTALLING THE SUPREMA FRONT BOARD REMOVING THE REAR CIRCUIT BOARD INSTALLING THE REAR BOARD REMOVING THE FUSE BOX ASSEMBLY ELECTRICAL WIRING DIAGRAMS Page / SUPREMA Page COIN CHANGER INSTALLATION INSTALLING THE PRICING DECALS