Everpure 2001 CAUTION:, REMOVING THE WATER TANK ASSEMBLY

SUPREMA 2001 - OPERATION & SERVICE MANUAL

REMOVING THE WATER TANK ASSEMBLY

1.Switch the coffee maker "OFF".

2.Drain the water tank.

a)Place a heat-resistant and leak-proof container beneath the water tank.

b)Remove the top clip on the drain plug and push the drain plug upwards. The bottom clip will act as a stopper.

CAUTION: Water coming out of the water tank may be extremely hot. Use caution when removing the outlet valves.

3.Remove the brewer.

4.Disconnect the inlet hose.

a)Remove the hose clamp securing the inlet hose to the inlet fitting.

5.Remove the valve cover on the water tank.

6.Remove the hose from the hot water valve.

7.Remove the hose fitting from the whipper motor (if installed).

8.Disconnect the water tank harness from the rear board.

9.Disconnect the temperature probe harness from the rear board.

10.Disconnect the wires identified in the table below.

WIRE	CONNECTED TO:
#1-2on General Harness	Whipper Motor
#8-1on General Harness	Whipper Motor
#11-1on Tank Harness	Wire #3-2on Fuse Box Harness
#6 on Tank Harness	Inlet Valve
#1-2on Tank Harness	Inlet Valve
#11 on Fuse Box Harness	Stud #3 on Heater Relay
#13-1(ground wire)	Ground Stud on Rear Board Cover

*For more information about wiring, consult the wiring section of this manual.

11. Carefully slide the water tank forward and out of the machine.

Page 46 of 60

July 6, 2001

Suprema 2001 - Operation & Service

Contents

Software Version TABLE OF CONTENTS DIFFERENCES BETWEEN THE VISTA 3 AND THE SUPREMA OVERVIEW OF SUPREMA COMPONENTS SELECTION PANELS & INTERIOR DOOR PANELS UNPACKING & SETTING UP THE EQUIPMENT REMOVING SHIPPING MATERIALS WARNING: CONNECTIONS AND ADJUSTMENTS APPLYING THE FASCIA APPLYING THE INNER DOOR DECALS INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL WATER CONNECTION INSTALLATION AT AN ACCOUNT CONNECTING TO A WATER SUPPLY RUNNING COPPER TUBING FINISHING TOUCHES PROGRAMMING THE EQUIPMENT COIN DISPENSE TOTAL PER SELECTION COUNTER TOTAL COUNTER RESET "TOTAL COUNTER RESET" ACCESS CODE SET-UPMODE & ACCESS CODE PRODUCT ON/OFF SETTING PRODUCTS SETTING WATER SETTING PRICES ENABLING SWITCHES CANCELING INDIVIDUAL SELECTIONS SETTING THE DEFAULT SETTING TOP PAUSE SETTING BOTTOM PAUSE SETTING THE MAXIMUM NUMBER OF CUPS PER CARAFE SETTING THE FREQUENCY OF MESSAGES SERVICE COUNTER SETTING BOTTOM PAUSE DELAY CANCELING MESSAGES (MESSAGES ON, OFF or "ACTIVE") FREE VEND KEY SWITCH SET-UP SETTING THE “EMPTY GROUNDS CONTAINER” MESSAGE SETTING NUMBER OF CHOCOLATE PUMP CYCLES SETTING THE DOUBLE-CUP SETTING THE TEMPERATURE PROGRAMMING A CUSTOM MESSAGE SETTING LANGUAGE SETTING THE WATER LEVEL PROBE SETTING THE POST-MIX LOCKING THE COUNTERS SETTING THE FORCE VEND FEATURE OPERATION INFORMATION PRIMING THE CHOCOLATE PUMP SYSTEM STATUS INDICATORS GENERAL INFORMATION RINSE CYCLES BREWER RINSE CYCLE DOWNLOADING SOFTWARE AND TRANFERRING SETTINGS Page TRANSFERRING SETTINGS FROM ONE SUPREMA TO ANOTHER STEP 1 - TRANSFERRING SETTINGS TO THE DATA LINK DEVICE STEP 2 - TRANSFERRING SETTINGS FROM THE DATA LINK DEVICE TO A SUPREMA STEP 3 - TRANSFERRING CUSTOM MESSAGES TO A SUPREMA INDICATOR MESSAGES Page CORRECTIVE ACTION REPLACING MAJOR COMPONENTS REMOVING THE BREWER MOTOR INSTALLING THE BREWER MOTOR REMOVING THE INLET VALVE INSTALLING THE INLET VALVE REMOVING THE OUTLET VALVES CAUTION: INSTALLING THE OUTLET VALVES REMOVING THE WATER TANK ASSEMBLY INSTALLING THE WATER TANK REMOVING THE WATER TANK LID ASSEMBLY INSTALLING THE WATER TANK LID ASSEMBLY REMOVING THE HEATER ELEMENT INSTALLING THE HEATER ELEMENT REMOVING THE DRAIN VALVE INSTALLING THE DRAIN VALVE REMOVING THE INGREDIENT DISPENSER INSTALLING THE INGREDIENT DISPENSER REMOVING AN INGREDIENT DISPENSER MOTOR INSTALLING AN INGREDIENT DISPENSER MOTOR REMOVING THE SUPREMA FRONT BOARD INSTALLING THE SUPREMA FRONT BOARD REMOVING THE REAR CIRCUIT BOARD INSTALLING THE REAR BOARD REMOVING THE FUSE BOX ASSEMBLY ELECTRICAL WIRING DIAGRAMS Page / SUPREMA Page COIN CHANGER INSTALLATION INSTALLING THE PRICING DECALS