Manuals / Brands / Kitchen Appliance / Hot Beverage Maker / Everpure / Kitchen Appliance / Hot Beverage Maker

Everpure 2001 WATER CONNECTION, INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL

1 60

Download 60 pages, 0 b

SUPREMA 2001 - OPERATION & SERVICE MANUAL

INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL

10.Install the carafe tray, cup stand and graphics bezel.

a)Install the carafe tray as illustrated below. Once done, install the cup stand on top of the carafe tray.

b)Install the bezel by first inserting the tabs on bottom if it into the notches on the door. Push the top of the bezel into the door until it clips in place.

◄

Install the carafe tray (and grill) and the cup stand (and grill).

►

Install the pre- assembled graphics (and pricing) bezel.

WATER CONNECTION

11.Connect the water supply to the coffee maker.

a)Apply Teflon tape to a 3/8" plumbing fitting. If a 1/4" line is being used, you will then need a 1/4 x 3/8" fitting.

!Note:

For initial water connection at your shop, we recommend using 1/4" polytubing, and an instant (quick connect) fitting. This will simplify water hook-up. For field installation, we recommend copper tubing from the source, all the way to the coffee maker.

♦ Teflon tape should be applied in a clockwise direction, going with the threads when tightening.

b)Thread the fitting into the inlet valve at the back of the coffee maker and tighten with a wrench.

d)Connect the water line to the fitting.

e)Turn the water on at the source.

f)Plug the coffee maker into the wall outlet.

12.Switch the coffee maker "ON".

a)The main power switch is found on the back of the coffee maker.

b)When the power is switched "ON", you should hear the coffee maker filling with water.

c)Check the plumbing for leaks and correct them, if necessary.

d)Check the display for any messages, and take the indicated action.

13.Fill the ingredient dispenser with coffee.

a)Open the front door of the coffee maker.

b)Lift the lid on top of the coffee maker.

c)One section of the ingredient dispenser is larger than the other. The large section is for the coffee that is expected to have higher consumption. The smaller is for decaffeinated or lower consumption blends.

d)Fill the ingredient dispensers by pouring coffee through the opening in the lid.

Page 8 of 60

July 6, 2001

Suprema 2001 - Operation & Service

Contents

Software Version TABLE OF CONTENTS DIFFERENCES BETWEEN THE VISTA 3 AND THE SUPREMA OVERVIEW OF SUPREMA COMPONENTS SELECTION PANELS & INTERIOR DOOR PANELS UNPACKING & SETTING UP THE EQUIPMENT REMOVING SHIPPING MATERIALS WARNING: CONNECTIONS AND ADJUSTMENTS APPLYING THE FASCIA APPLYING THE INNER DOOR DECALS INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL WATER CONNECTION INSTALLATION AT AN ACCOUNT CONNECTING TO A WATER SUPPLY RUNNING COPPER TUBING FINISHING TOUCHES PROGRAMMING THE EQUIPMENT COIN DISPENSE TOTAL PER SELECTION COUNTER TOTAL COUNTER RESET "TOTAL COUNTER RESET" ACCESS CODE SET-UPMODE & ACCESS CODE PRODUCT ON/OFF SETTING PRODUCTS SETTING WATER SETTING PRICES ENABLING SWITCHES CANCELING INDIVIDUAL SELECTIONS SETTING THE DEFAULT SETTING TOP PAUSE SETTING BOTTOM PAUSE SETTING THE MAXIMUM NUMBER OF CUPS PER CARAFE SETTING THE FREQUENCY OF MESSAGES SERVICE COUNTER SETTING BOTTOM PAUSE DELAY CANCELING MESSAGES (MESSAGES ON, OFF or "ACTIVE") FREE VEND KEY SWITCH SET-UP SETTING THE “EMPTY GROUNDS CONTAINER” MESSAGE SETTING NUMBER OF CHOCOLATE PUMP CYCLES SETTING THE DOUBLE-CUP SETTING THE TEMPERATURE PROGRAMMING A CUSTOM MESSAGE SETTING LANGUAGE SETTING THE WATER LEVEL PROBE SETTING THE POST-MIX LOCKING THE COUNTERS SETTING THE FORCE VEND FEATURE OPERATION INFORMATION PRIMING THE CHOCOLATE PUMP SYSTEM STATUS INDICATORS GENERAL INFORMATION RINSE CYCLES BREWER RINSE CYCLE DOWNLOADING SOFTWARE AND TRANFERRING SETTINGS Page TRANSFERRING SETTINGS FROM ONE SUPREMA TO ANOTHER STEP 1 - TRANSFERRING SETTINGS TO THE DATA LINK DEVICE STEP 2 - TRANSFERRING SETTINGS FROM THE DATA LINK DEVICE TO A SUPREMA STEP 3 - TRANSFERRING CUSTOM MESSAGES TO A SUPREMA INDICATOR MESSAGES Page CORRECTIVE ACTION REPLACING MAJOR COMPONENTS REMOVING THE BREWER MOTOR INSTALLING THE BREWER MOTOR REMOVING THE INLET VALVE INSTALLING THE INLET VALVE REMOVING THE OUTLET VALVES CAUTION: INSTALLING THE OUTLET VALVES REMOVING THE WATER TANK ASSEMBLY INSTALLING THE WATER TANK REMOVING THE WATER TANK LID ASSEMBLY INSTALLING THE WATER TANK LID ASSEMBLY REMOVING THE HEATER ELEMENT INSTALLING THE HEATER ELEMENT REMOVING THE DRAIN VALVE INSTALLING THE DRAIN VALVE REMOVING THE INGREDIENT DISPENSER INSTALLING THE INGREDIENT DISPENSER REMOVING AN INGREDIENT DISPENSER MOTOR INSTALLING AN INGREDIENT DISPENSER MOTOR REMOVING THE SUPREMA FRONT BOARD INSTALLING THE SUPREMA FRONT BOARD REMOVING THE REAR CIRCUIT BOARD INSTALLING THE REAR BOARD REMOVING THE FUSE BOX ASSEMBLY ELECTRICAL WIRING DIAGRAMS Page / SUPREMA Page COIN CHANGER INSTALLATION INSTALLING THE PRICING DECALS