Manuals / Brands / Kitchen Appliance / Hot Beverage Maker / Everpure / Kitchen Appliance / Hot Beverage Maker

Everpure 2001 REPLACING MAJOR COMPONENTS, REMOVING THE BREWER, INSTALLING THE BREWER

1 60

Download 60 pages, 0 b

SUPREMA 2001 - OPERATION & SERVICE MANUAL

REPLACING MAJOR COMPONENTS

REMOVING THE BREWER

1.Press the red "OPEN BREWER" button.

a)The brewer motor will cycle and stop with the chamber in the open position.

2. Release the brewer lock pin.

a)Lower the lock pin by pulling it down all the way.

b)Turn the pin to the left until it is directly below

the flange, and release.

3. Remove the brewer from the brewer bracket.

a) Gently grasp the brewer with one hand on the top, and the other hand on the bottom.

b) Pull the brewer towards you until it is free from
the bracket.	Brewer lock pin
	Brewer lock pin

INSTALLING THE BREWER

1.Press the red "OPEN BREWER" button.

a)The brewer motor will cycle and stop in a position where it will accept the brewer with the chamber open.

2.Place the brewer onto the brewer bracket.

a)Make sure that the brew chamber is open.

b)Gently grasp the brewer, with one hand on the top, and the other hand on the bottom.

c)Align the top edge of the brewer with the locating flanges on the brewer bracket. One flange is at the left side of the bracket and the other is at the back of the bracket.

d)Push the brewer into place to engage the brewer drive pin with the slot in the motor coupling. If it does not align, move the brewer crank arm slightly until you feel the brewer engaging with the motor coupling.

3.Engage the lock pin.

a)Release the lock pin from under the front flange and engage it with the hole located on the front left side of the brewer. The brewer should now be firmly in place.

Page 42 of 60

July 6, 2001

Suprema 2001 - Operation & Service

Contents

Software Version TABLE OF CONTENTS DIFFERENCES BETWEEN THE VISTA 3 AND THE SUPREMA OVERVIEW OF SUPREMA COMPONENTS SELECTION PANELS & INTERIOR DOOR PANELS UNPACKING & SETTING UP THE EQUIPMENT REMOVING SHIPPING MATERIALS WARNING: CONNECTIONS AND ADJUSTMENTS APPLYING THE FASCIA APPLYING THE INNER DOOR DECALS INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL WATER CONNECTION INSTALLATION AT AN ACCOUNT CONNECTING TO A WATER SUPPLY RUNNING COPPER TUBING FINISHING TOUCHES PROGRAMMING THE EQUIPMENT COIN DISPENSE TOTAL PER SELECTION COUNTER TOTAL COUNTER RESET "TOTAL COUNTER RESET" ACCESS CODE SET-UPMODE & ACCESS CODE PRODUCT ON/OFF SETTING PRODUCTS SETTING WATER SETTING PRICES ENABLING SWITCHES CANCELING INDIVIDUAL SELECTIONS SETTING THE DEFAULT SETTING TOP PAUSE SETTING BOTTOM PAUSE SETTING THE MAXIMUM NUMBER OF CUPS PER CARAFE SETTING THE FREQUENCY OF MESSAGES SERVICE COUNTER SETTING BOTTOM PAUSE DELAY CANCELING MESSAGES (MESSAGES ON, OFF or "ACTIVE") FREE VEND KEY SWITCH SET-UP SETTING THE “EMPTY GROUNDS CONTAINER” MESSAGE SETTING NUMBER OF CHOCOLATE PUMP CYCLES SETTING THE DOUBLE-CUP SETTING THE TEMPERATURE PROGRAMMING A CUSTOM MESSAGE SETTING LANGUAGE SETTING THE WATER LEVEL PROBE SETTING THE POST-MIX LOCKING THE COUNTERS SETTING THE FORCE VEND FEATURE OPERATION INFORMATION PRIMING THE CHOCOLATE PUMP SYSTEM STATUS INDICATORS GENERAL INFORMATION RINSE CYCLES BREWER RINSE CYCLE DOWNLOADING SOFTWARE AND TRANFERRING SETTINGS Page TRANSFERRING SETTINGS FROM ONE SUPREMA TO ANOTHER STEP 1 - TRANSFERRING SETTINGS TO THE DATA LINK DEVICE STEP 2 - TRANSFERRING SETTINGS FROM THE DATA LINK DEVICE TO A SUPREMA STEP 3 - TRANSFERRING CUSTOM MESSAGES TO A SUPREMA INDICATOR MESSAGES Page CORRECTIVE ACTION REPLACING MAJOR COMPONENTS REMOVING THE BREWER MOTOR INSTALLING THE BREWER MOTOR REMOVING THE INLET VALVE INSTALLING THE INLET VALVE REMOVING THE OUTLET VALVES CAUTION: INSTALLING THE OUTLET VALVES REMOVING THE WATER TANK ASSEMBLY INSTALLING THE WATER TANK REMOVING THE WATER TANK LID ASSEMBLY INSTALLING THE WATER TANK LID ASSEMBLY REMOVING THE HEATER ELEMENT INSTALLING THE HEATER ELEMENT REMOVING THE DRAIN VALVE INSTALLING THE DRAIN VALVE REMOVING THE INGREDIENT DISPENSER INSTALLING THE INGREDIENT DISPENSER REMOVING AN INGREDIENT DISPENSER MOTOR INSTALLING AN INGREDIENT DISPENSER MOTOR REMOVING THE SUPREMA FRONT BOARD INSTALLING THE SUPREMA FRONT BOARD REMOVING THE REAR CIRCUIT BOARD INSTALLING THE REAR BOARD REMOVING THE FUSE BOX ASSEMBLY ELECTRICAL WIRING DIAGRAMS Page / SUPREMA Page COIN CHANGER INSTALLATION INSTALLING THE PRICING DECALS