Manuals / Brands / Kitchen Appliance / Hot Beverage Maker / Everpure / Kitchen Appliance / Hot Beverage Maker

Everpure 2001 WARNING:, SETTING LANGUAGE, SETTING THE WATER LEVEL PROBE

1 60

Download 60 pages, 0 b

SUPREMA 2001 - OPERATION & SERVICE MANUAL

SETTING LANGUAGE

!Note:

If “ENGLISH +

FRENCH” is selected, the messages on the display will continuously toggle from English to French approximately every three seconds.

The messages that appear on the LCD can be displayed in either English or French. Please note that the coffee maker will be shipped from the factory with the messages set to English.

1.To set the language, press the "UP" button on the hidden menu scroll buttons and scroll until the following message appears,

SET LANGUAGE

PRESS <START>

a)Press the "START" button to enter the set mode.

b)Using the hidden setting adjustment buttons, select “ENGLISH”, or

“FRENCH”, or “ENGLISH + FRENCH”.

c)To save, press either one of the two hidden menu scroll buttons.

SETTING THE WATER LEVEL PROBE

When scrolling through the "SET-UP" mode, you will notice a setting in the menu that reads,

SET WATER LEVEL

PRESS <START>

1.Press "START" to access this menu.

a)Using the hidden adjustment buttons, change the setting from

"MECHANICAL SWITCH" to "ELECTRONIC PROBE".

b)Exit the “SET-UP” mode.

WARNING: Do not access this menu if the machine is not equipped with the electronic water level probes.

Suprema 2001 - Operation & Service

July 6, 2001

Page 27 of 60

Contents

Software Version TABLE OF CONTENTS DIFFERENCES BETWEEN THE VISTA 3 AND THE SUPREMA OVERVIEW OF SUPREMA COMPONENTS SELECTION PANELS & INTERIOR DOOR PANELS UNPACKING & SETTING UP THE EQUIPMENT REMOVING SHIPPING MATERIALS WARNING: CONNECTIONS AND ADJUSTMENTS APPLYING THE FASCIA APPLYING THE INNER DOOR DECALS INSTALLING THE CARAFE TRAY, CUP STAND AND GRAPHICS BEZEL WATER CONNECTION INSTALLATION AT AN ACCOUNT CONNECTING TO A WATER SUPPLY RUNNING COPPER TUBING FINISHING TOUCHES PROGRAMMING THE EQUIPMENT COIN DISPENSE TOTAL PER SELECTION COUNTER TOTAL COUNTER RESET "TOTAL COUNTER RESET" ACCESS CODE SET-UPMODE & ACCESS CODE PRODUCT ON/OFF SETTING PRODUCTS SETTING WATER SETTING PRICES ENABLING SWITCHES CANCELING INDIVIDUAL SELECTIONS SETTING THE DEFAULT SETTING TOP PAUSE SETTING BOTTOM PAUSE SETTING THE MAXIMUM NUMBER OF CUPS PER CARAFE SETTING THE FREQUENCY OF MESSAGES SERVICE COUNTER SETTING BOTTOM PAUSE DELAY CANCELING MESSAGES (MESSAGES ON, OFF or "ACTIVE") FREE VEND KEY SWITCH SET-UP SETTING THE “EMPTY GROUNDS CONTAINER” MESSAGE SETTING NUMBER OF CHOCOLATE PUMP CYCLES SETTING THE DOUBLE-CUP SETTING THE TEMPERATURE PROGRAMMING A CUSTOM MESSAGE SETTING LANGUAGE SETTING THE WATER LEVEL PROBE SETTING THE POST-MIX LOCKING THE COUNTERS SETTING THE FORCE VEND FEATURE OPERATION INFORMATION PRIMING THE CHOCOLATE PUMP SYSTEM STATUS INDICATORS GENERAL INFORMATION RINSE CYCLES BREWER RINSE CYCLE DOWNLOADING SOFTWARE AND TRANFERRING SETTINGS Page TRANSFERRING SETTINGS FROM ONE SUPREMA TO ANOTHER STEP 1 - TRANSFERRING SETTINGS TO THE DATA LINK DEVICE STEP 2 - TRANSFERRING SETTINGS FROM THE DATA LINK DEVICE TO A SUPREMA STEP 3 - TRANSFERRING CUSTOM MESSAGES TO A SUPREMA INDICATOR MESSAGES Page CORRECTIVE ACTION REPLACING MAJOR COMPONENTS REMOVING THE BREWER MOTOR INSTALLING THE BREWER MOTOR REMOVING THE INLET VALVE INSTALLING THE INLET VALVE REMOVING THE OUTLET VALVES CAUTION: INSTALLING THE OUTLET VALVES REMOVING THE WATER TANK ASSEMBLY INSTALLING THE WATER TANK REMOVING THE WATER TANK LID ASSEMBLY INSTALLING THE WATER TANK LID ASSEMBLY REMOVING THE HEATER ELEMENT INSTALLING THE HEATER ELEMENT REMOVING THE DRAIN VALVE INSTALLING THE DRAIN VALVE REMOVING THE INGREDIENT DISPENSER INSTALLING THE INGREDIENT DISPENSER REMOVING AN INGREDIENT DISPENSER MOTOR INSTALLING AN INGREDIENT DISPENSER MOTOR REMOVING THE SUPREMA FRONT BOARD INSTALLING THE SUPREMA FRONT BOARD REMOVING THE REAR CIRCUIT BOARD INSTALLING THE REAR BOARD REMOVING THE FUSE BOX ASSEMBLY ELECTRICAL WIRING DIAGRAMS Page / SUPREMA Page COIN CHANGER INSTALLATION INSTALLING THE PRICING DECALS