Extron electronic manual The USP 507 complete menu list, USP 507 Front Panel Operation

User Menu

Presets

Input Menu

Configuration

Output Menu

Configuration

Image Menu Advanced Menu

Capture/RecallConfiguration

View Comm	Menu
Settings

Exit Menu	**N
Press NEXT

The Scan Coverter Settings menu is available only when an optional Scan Converter

Next

Recall Preset <NA>

Rotate either to select a preset to recall settings.

Next

Save Preset <02>

Rotate either

to select a preset to save current settings to.

Next

Input #x

RGB

Rotate to select video input type.

Next

Input #x

Film Detect On

Rotate to turn Film Detect on or off.

Next

Next

Resol 1024x768

Refresh 60.00Hz

Rotate to adjust

Resolution value

Rotate to adjust

Refresh rate.

Next

Output Type

RGBHV

Rotate either to adjust Output type value.

Next

Save Image

<N/A>

Rotate either to select an image name.

Next

Recall to Back

<N/A>

Rotate either to select an image name.

Next

	Next
Auto Image
Input #x	Off

Rotate either to turn auto image on

or off.

Next

Input EDID

1024x768 60.0Hz

Rotate to adjust resolution value rotate to adjust refresh rate.

Next

Serial Port

9600 RS232

Next

MAC Address 005A6003C24

This is set at the factory and cannot be changed in Edit Comm Settings menu.

Next

DHCP Mode

On

I/O board is installed.

Optional I/O

Board Menu **

Scan Converter

Settings

Next

H Size V

2048 2048

Rotate to adjust H value. Rotate to adjust V value.

Next

Input #x

Vert Start 128

Rotate to adjust Vertical Start value.

Next

Input #x

Horz Start 128

	Next
Sync Polarity
H Neg	V Pos

Rotate either to adjust Sync Polarity values.

Recall to Front

<N/A>

Rotate either to select an image name.

Next

Auto Memories

On

Rotate either to turn auto memories on or off.

Next

Next

IP Address

192.168.254.254

Next

Subnet Mask

255.255.000.000

Next

*N To activate the hidden menu “Edit Comms”, press and hold Detail and Color/Tint buttons simultaneously, then press Next.

“Hidden” Edit Comms Menu *

Edit Comm

H Center V

2048 2048

Rotate to adjust H value. Rotate to adjust V value.

Next

Output Format

S-video/Comp

USP 507 • Front Panel Operation

Rotate to adjust

Horizontal Start value.

Next

Input #x

Pixel Phase 28

Rotate to adjust

Pixel Phase value.

Next

Input #x

Total Pix *2200

Rotate to adjust Total Pixel value (* = default).

Next

Input #x

Active Pixels *1920

Rotate to adjust Active Pixels value (* = default).

Next

Input #x

Active Lns *1080

Rotate to adjust Active Lines value (* = default).

RGB Delay

0.5 Seconds

Rotate either to adjust

RGB delay value.

Next

Switch Effect

Cut (Blank)

Rotate either to change switch effect.

Next

Test Pattern

Color bars

Rotate either to change test pattern.

Next

MTP Pre-Peaking

Off

Rotate either to turn MTP pre-peaking on or off.

Next

Internal temp

96 F 35 C

Indicates internal temperature (not adjustable).

Gateway Address 000.000.000.000

Settings

Next

Serial Port

9600 RS232

Rotate to select RS-232 or RS-422 mode. Rotate to change baud rate.

Next

DHCP Mode

<On>

Rotate either to turn

DHCP mode On or Off.

Next

IP Address

<192>168.254.254

Rotate to select octet field. Rotate to change address.

Next

Subnet Mask

<255>255.000.000

Rotate to select octet field. Rotate to change address.

Next

Gateway Address

Rotate either to select output format.

Next

Output Standard

NTSC

Rotate either to select output standard.

Next

Flicker Filter

3

Rotate either to adjust flicker filter.

Next

HFilter 0

Rotate either to adjust H filter.

Next

Encoder Filter

0

Rotate either to adjust encoder filter.

3-5

	Next
	Reset to Factory
	Press Detail
The USP 507 complete menu list	Press Detail to reset unit
	to factory settings.

<000>000.000.000

Rotate to select octet field. Rotate to change address.