Extron electronic USP 507 manual Input configuration, 4— Adjustments possible per signal form

Models: USP 507

1 96
Download 96 pages 45.48 Kb
Page 27
Image 27
Input configuration

Input configuration

Within this menu any of the seven inputs can be configured. Each input has different settings depending on the signal format. Consult the tables below for signal formats per input and possible adjustments per signal format.

To configure inputs:

1. From the top level Input Configuration menu press the Next

Input #2

button to bring up the input selection screen. The active

YUVp/HDTV

input is displayed on the LCD with current signal format.

 

NIf the input showing is not the one to be adjusted, press the desired input button.

2.

With the correct input displayed, rotate the right Adjust knob ({) to change

 

the signal format (refer to table below for signal type per input).

 

 

 

 

 

 

 

 

 

 

Input #1

 

Input #2

Input #3

Input #4

Input #5

Input #6

 

Input #7

 

 

 

 

 

 

 

 

 

*RGB

 

*RGB

*RGB

*YUVi

*S-Video

*DVI

 

*SDI

 

 

 

 

 

 

 

 

 

YUVp/HDTV

 

YUVp/HDTV

YUVp/HDTV

S-Video

Composite

 

 

HD-SDI

 

 

 

 

 

 

 

 

 

Auto Detect

 

Auto Detect

RGBcvS

Composite

Auto Detect

 

 

Auto Detect

 

 

 

 

 

 

 

 

 

 

 

 

YUVi

Auto Detect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S-Video

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Composite

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Detect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3-3 — Signal formats per input (*= default value)

3.

Press the Next button to go to the next setting. If necessary repeat pressing

 

Next until the desired level is attained. Refer to the table below for adjustable

 

settings for each signal format.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Format

RGB

YUVp/

RGBcvS

YUVi

S-vid

Composite

DVI

SDI

HD-SDI

 

 

 

HDTV

 

 

 

Video

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Film Detect

 

X

X

X

X

X

X

X

X

X

 

 

 

 

 

 

 

 

 

 

 

H Start

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V Start

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phase

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Total Pixels

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Active Pixels

 

X

X

X

X

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

 

Active Lines

 

X

X

X

X

X

X

 

X

X

 

 

 

 

 

 

 

 

 

 

Figure 3-4 — Adjustments possible per signal form

 

 

 

4.

At the desired setting (for example, Horizontal Start on input #2 with a

 

YUVp/HDTV signal), rotate the right Adjust knob ({) to adjust the settings

 

value as desired (here to 122).

 

 

 

 

 

5.

Repeat steps 3 and 4 for each setting as desired.

 

 

 

6.

When complete press Menu once or Next repeatedly to return to the top level

 

menu. Alternatively, allow to time out to return to the default cycle.

 

USP 507 • Front Panel Operation

3-7

Page 27
Image 27
Extron electronic manual Input configuration, 4— Adjustments possible per signal form, USP 507 Front Panel Operation