Manuals / Extron electronic / Home Audio / Stereo System

Extron electronic USP 507 manual Reference Information, Specifications

Models: USP 507

1 96

Download 96 pages 45.48 Kb

Page 86

Reference Information

Specifications

Video input

Number/signal type	2 RGBHV, RGBS, RGsB, component video (Y, R-Y, B-Y; progressive or HD)
	1 RGBHV, RGBS, RGsB, component (Y, R-Y, B-Y; interlaced, progressive, HD)
	S-video, composite video
	1 component video (Y, R-Y, B-Y; interlaced), S-video, composite video
	1 S-video, composite video
	1 single link DVI-D
	1 optional SDI, HD-SDI
Connectors	2 female 15-pin HD: RGBHV, RGBS, RGsB, component video
	5 female BNC: RGBHV, RGBS, RGsB, component video, S-video, composite
	video
	3 female BNC: component video, S-video, composite video
	2 female BNC: S-video, composite video
	1 female DVI-I: DVI-D
	1 female BNC: optional SDI, HD-SDI
Nominal level	1 Vp-p for Y of component video and S-video, and for composite video
	0.8 Vp-p for SDI
	0.7 Vp-p for RGB and for R-Y and B-Y of component video
	0.3 Vp-p for C of S-video
Minimum/maximum levels	Analog: 0.0 V to 2.0 Vp-p with no offset
Impedance	75 ohms
Horizontal frequency	Autoscan 15 kHz to 100 kHz
Vertical frequency	Autoscan 24 Hz to 120 Hz
Resolution range	640x480 to 1920x1200*, 480p, 576p, 720p, 1080i, and 1080p, digitized pixel for
	pixel; higher resolutions are undersampled.
	*Reduced blanking
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	0.5 V

Video processing

Digital sampling	30 bit, 10 bits per color; 13.5 MHz standard (video),
	165 MHz standard (RGB, YUVp, DVI)
Colors	1 billion, 1024 per color channel

Encoder (for scan converted output)

10 bit digital

Horizontal filtering (for scan converted output) 3 levels

Vertical filtering (for scan converted output) 3 levels

Encoder filtering (for scan converted output) 3 levels

Video output

Number/signal type	2 buffered scaled RGBHV, RGBS, RGsB, or scaled HD component video
	(Y, R-Y, B-Y)
	1 MTP
	1 optional single link DVI-D; HD-SDI; or interlaced component video,
	S-video, composite video
Connectors	6 female BNC: RGB or component video
	1 female 15-pin HD: RGB or component video
	1 female RJ-45: output to an MTP device
	1 slot for an optional DVI-D, HD-SDI, or interlaced component, S-video,
	composite video output card

A-2 USP 507 • Reference Information

Image 86

Extron electronic manual Specifications, A-2USP 507 • Reference Information

Contents

Universal Signal Processor Rev. AConsignes de Sécurité • Français PrecautionsSafety Instructions English Sicherheitsanleitungen • DeutschFCC Class A Notice Table of Contents USP 507 • Table of ContentsTable of Contents, cont’d Installing and Starting the Signal Processing USP 507 • Table of ContentsTable of Contents, cont’d ivUSP 507 • Table of ContentsIntroduction FeaturesChapter1One About this Manual About the USP DefinitionsAbout the USP IntroductionAbout this Manual Figure 1-1— Typical USP 507 applicationDefinitions USP 507 • Introduction1-4USP 507 Introduction FeaturesIntroduction, cont’d USP 507 • Introduction Rear Panel Features and Connections Powering Up InstallationU/L Safety Requirements Mounting the USP Resetting the Unit with the Reset ButtonImportant safety instructions Installationstallation, cont’dUL/Safety Requirements 2-2USP 507 • InstallationUL guidelines for rack mounted devices Tabletop placementMounting the USP Rack mountingPower and video input connections Installation, cont’dRear Panel Features and Connections 2-4USP 507 • InstallationOutput, user interface, and control connections USP 507 • Installation2-6USP 507 • Installation Installation and cablingInstallation, cont’d Default display cycle Powering UpResetting the Unit with the Reset Button Default Display Cycle2-8USP 507 Installation Installation, cont’dUSP 507 Reset Mode Summary This Mode performs a complete reset to factoryChapter3Three Front Panel Overview Switching InputsSetting the Front Panel Locks Executive Modes Front Panel OperationFigure 3-1— Front panel features Front Panel OperationFront Panel Overview 3-2USP 507 Front Panel OperationButton Backlighting Switching InputsSpecial Function Button Operation USP 507 Front Panel OperationOverview of menus FrontPanelOperation,co t’dThe USP 507 Menu System User PresetsThe USP 507 complete menu list USP 507 Front Panel OperationFront Panel Operation, cont’d Using the menusUser presets Save a user presetUSP 507 Front Panel Operation Input configurationFigure 3-4— Adjustments possible per signal form Front Panel Operation, cont’d Output configurationFigure 3-5— Output resolution/refresh rate table 3-8USP 507 • Front Panel OperationTo recall an image Image capture/recallTo capture an image USP 507 • Front Panel OperationTo remove an image from the display Advanced configurationFront Panel Operation, cont’d 3-10USP 507 • Front Panel OperationAuto-Imageon or off USP 507 • Front Panel OperationExit menu View comm settingsEdit comm settings Front Panel Operation, cont’dExecutive Mode Enabled Setting the Front Panel Locks Executive ModesScan converter configuration Executive Mode DisabledFront Panel Operation, cont’d 3-14USP 507 • Front Panel OperationUSP 507 • Front Panel Operation Click Connect to Matrix button. TheUSP 507 Input #3 select the matrix 3-16USP 507 Front Panel Operation Front Panel Operation, cont’dFigure 3-10— Controller to USP 507 pinout SIS Programmer’s Guide Processor Error ResponsesChapter4Four RS-232/RS-422Link Ethernet LAN\⤀ PortRS-232/RS-422Link Default IP addressesSIS Programmer’s Guide Ethernet LAN\⤀ PortHost-to-ProcessorInstructions Connection timeoutsUsing verbose mode Processor-InitiatedMessagesSIS Programmer’s Guide, cont’d Processor Error ResponsesUsing the Command/Response Table for SIS Commands ASCII to hexadecimal conversionSymbol definitions USP 507 • SIS Programmer’s GuideSIS Programmer’s Guide, cont’d 4-6USP 507 • SIS Programmer’s GuideCommand Response Table for SIS Commands SIS Programmer’s Guide, cont’d E X^PHASE X1%COLR SIS Programmer’s Guide, cont’d E X1&HSIZE X2!*X2@RATE SIS Programmer’s Guide, cont’d ESX1&HSIZAdvanced Configurations CommandASCII command RGB delay timeSIS Programmer’s Guide, cont’d CommandASCII command ResponseResets CommandASCII command Response4-16USP 507 • SIS Programmer’s Guide Symbol definitionsSIS Programmer’s Guide, cont’d Command/Response Table for IP SIS Commands SIS Programmer’s Guide, cont’d EX12#CVEX12%*X14#*X14$ Command Programmer’sGuide, cont’d File commandsUSP 507 Software Using the ProgramChapter5Five Starting the program Installing the programUSP 507 Software 5-2USP 507 • USP 507 SoftwareFigure 5-1— The control program main window Using the ProgramOrientation USP 507 USP 507 SoftwareFile menu USP 507 Software, cont’dControl program menus Options menuTools menu USP 507 • USP 507 Software5-6USP 507 • USP 507 Software USP 507 Software, cont’dDownload Now USP 507 • USP 507 Software Figure 5-2— The SPPCP Help file’s main window USP 507 Software, cont’dHelp menu 5-8USP 507 • USP 507 SoftwareUSP 507 • USP 507 Software Control tabFigure 5-3— The Control tab screen USP 507 Software, cont’d I/O Configuration tabFigure 5-4— The I/O Configuration tab screen 5-10USP 507 • USP 507 SoftwareUSP 507 • USP 507 Software Advanced Settings tabFigure 5-5— The Advanced Settings tab screen Figure 5-6— The Scan Converter tab screen Scan Converter tabUSP 507 Software, cont’d 5-12USP 507 • USP 507 SoftwareFigure 5-7— The Image Capture tab screen Image Capture tabStatus bar USP 507 • USP 507 SoftwareChapter6Six Accessing the Web Pages System Status PageConfiguration Pages File Management Page HTML Operation6-2USP 507 • HTML Operation Accessing the Web PagesHTML Operation USP 507 • HTML Operation System Status PageFigure 6-2 — System Status page HTML Operation, cont’d Configuration PagesSystem Settings page Figure 6–3 — System Configuration pageGateway IP Address field DHCP radio buttonsIP Address field Subnet Mask fieldHTML Operation, cont’d Date/Time Settings fieldsFigure 6–4 — Date/Time Settings fields 6-6USP 507• HTML OperationInput configuration Scaler Settings pageFigure 6–5 — Scaler settings page USP 507 • HTML OperationHTML Operation, cont’d Output configurationAdvanced configuration 6-8USP 507• HTML OperationUSP 507 • HTML Operation Passwords pageFigure 6–7 — Passwords page HTML Operation, cont’d Firmware Upgrade pageFigure 6–8 — Firmware Upgrade page Download product name_firmware version.exe buttonUSP 507 HTML Operation File Management PageFigure 6–10 — File Management page Other file management activities Uploading filesAdding a directory HTML Operation, cont’dFigure 6-11 - User Control page Control PagesUser Control page USP 507 • HTML OperationFigure 6–12 — Presets page Memory/Input Presets pagePIP Setup/PIP Presets page HTML Operation, cont’dUSP 507 • HTML Operation Images PageFigure 6–14 — Images page AAppendix A Specifications Part Numbers and AccessoriesReference Information A-2USP 507 • Reference Information SpecificationsReference Information USP 507 • Reference Information Control/remote— signal processorSync A-4USP 507 • Reference Information Reference Information, cont’dGeneral Included parts Part Numbers and AccessoriesAccessories Optional I/O boardsEthernet Link Subnetting — A Primer AppendixBBEthernet Connection Ethernet Link Default addressEthernet Connection Figure B–1— RJ-45connector pinout tablesPing to determine Web IP address Connect as a Telnet clientFigure B–2— Ping response Figure B–3— Telnet screenConnecting to the USP 507 Open command\⤀ Ethernet Connection, cont’dTelnet tips Escape character and Esc keyLocal and remote devices Subnetting — A PrimerGateways IP addresses and octetsFigure B–5 — Subnet mask and octets Subnet masks and octetsEthernet Connection, cont’d Figure B–6 — Comparing the IP addressesJapan Extron WarrantyUSA, Canada, South America and Central America