Removing a hot-plug expansion card | Fujitsu RX600 S6 specs

CSS components

8.1.4.1Identifying the defective CSS component

ÊOpen the server (see "Opening/Closing the server" on page 125).

ÊPress the Indicate CSS button on the system board (see the "System Board D3141 for PRIMERGY RX600 S6 Technical Manual" on the ServerView Suite DVD 2).

The PRIMERGY Diagnostic LED of the defective CSS component lights up orange, thereby indicating which CSS component on the system board must be replaced (see the "System Board D3141 for PRIMERGY RX600 S6 Technical Manual" for details).

8.1.4.2Removing a hot-plug expansion card

ÊIf required by the operating system, start the PCI hot-plug software. You will find information about this in the readme file on the ServerView Suite DVD 2).

Figure 23: Deactivating, unlocking and removing the board

ÊDeactivate the expansion card using either the relevant PCI hot-plug software or by pressing the light-pipe switch (1).

ÊWait until the light-pipe switch (1) no longer lights up. The slot is now zero potential.

ÊIf necessary, remove all cables from the expansion card.

RX600 S6

Operating Manual

103

Image 103

Fujitsu RX600 S6 manual CSS components Identifying the defective CSS component, Removing a hot-plug expansion card

Contents

Primergy RX600 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections… Aluminum electrolytic capacitors For your safetyHigh safety use Radio interference Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Non-hot-plug components Opening/Closing the server Concept and target groups for this manual Preface Preface Documentation overview Further sources of information Customer Self Service CSS Features Hot-plug PCI slots Battery Backup UnitsAccessible drives/components Preface System board Cooling Power supplyHigh level of availability and data security Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation Manager Preface ServerView Remote Management Electrical data hot-plug power supply unit Technical dataNotational conventions Compliance with regulations and standards Noise level Preface Dimensions / WeightVentilation clearance Ambient conditions Overview of the installation steps Overview of the installation steps Important information Safety instructions Important information Before starting up Installation and operation Important information Important information Batteries RX600 S6 Never remove parts of the optical drive casing Laser information ESD label Important information Other important information CE conformity FCC Class a Compliance Statement Transporting the server Operating Manual Packaging information Environmental protectionEnvironmentally-friendly product design and development Energy-saving information Returns, recycling and disposal Important information Labels on plastic casing parts Hours Minimum acclimatization time Unpacking the server Hardware installation Rack system requirements Rack installation/removal of serverFujitsu rack systems 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connectors on the front Connecting devices to the server Connectors on the rear Connecting the monitor PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mainsInstallation requirements Installation requirements for AC redundant configurations +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Cable clamps to secure the power cords Connecting the power cord Disconnecting cables Connecting cables Hardware installation Front of server Control elements and indicators ID card Starting up and operation Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Rear of server Global Error indicator and CSS indicator Starting up and operation ID indicator Starting up and operation ID indicator and button LAN Indicators on the power supply units Indicators on the hot-plug power supply units Starting up and operation Switching the server on Switching the server on and offStarting up for the first time Ring indicator Starting up and operation System already installedSwitching the server off Timer-controlled switch-on/off IRMC S2 Configuring the SAS/SATA RAID controller card Configuring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Bios Setup security functions Mechanical access protection Property and data protection Server Management has detected an error Power-on indicator remains unlitServer switches itself off Power cable incorrectly connected Screen remains blank No screen display or display drifts Flickering stripes on monitor screenMonitor does not support the set horizontal frequency Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect RAID controller is not configured for this drive Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug components Hot-plug power supply units Vcaution CSS components Replacing a hot-plug power supply unit Removing a PSU dummy module Adding a hot-plug power supply unit CSS components Identifying the defective CSS component Hot-plug fans Unlocking a fan module and removing it CSS components Replacing a defective fan CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules Modules on 3.1 HDD/SSD module and dummy module Removing/installing the 2.5-inch dummy module CSS components Removing/installing the dummy module Unlocking the 2.5-inch HDD/SSD module CSS components Installing the HDD/SSD module Removing the HDD/SSD module Installing the 2.5-inch HDD/SSD module CSS components Hot-plug expansion cards PCI slots with and without hot-plug functionality Slot # Description Removing a hot-plug expansion card CSS components Identifying the defective CSS component Removing the expansion card from the removal tool Removing an expansion card from the removal tool Removing engaging hooks from the removal tool CSS components Removing engaging hooks Removing the retaining plate from the removal tool CSS components Removing a dummy module Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards Open the server see Opening the server on CSS components Identifying the defective memory Removing a defective memory module CSS components Removing the memory board in question Removing a memory module Reinstalling the memory board in question CSS components Installing a new memory module Removing the memory air baffle to add a memory board Adding a memory board Operating Manual 115 Non-hot-plug components Replacing a non-hot-plug expansion card Identifying the defective CSS componentRemoving a non-hot-plug expansion card Inserting the new expansion card CSS components Installing a non-hot-plug expansion card Removing an SFP+ transceiver module Replacing SFP+ transceiver modules Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening the server Opening/Closing the server Opening the server Closing the server Placing the housing cover 128 Operating Manual Processor Memory Modules Configuration Onboard or integrated controllers Appendix server specification InterfacesSlots At system rear side Drive baysGeneral system information Operating Panel Dimensions Base unit specific Appendix server specificationEnvironmental Electrical values 134 Operating Manual