Vcaution | Fujitsu RX600 S6 specs

CSS components

8.1.1.1Replacing a hot-plug power supply unit

Figure 14: Unlocking and removing the power supply unit

VCAUTION!

When replacing a non-defective hot-plug power supply unit in a non- redundant configuration, the server must be switched off first.

ÊRemove the power cord from the cable clamp. You can losen the cable clamp by opening the small locking lever.

ÊRemove the power cord from the installed power supply unit.

ÊPress the green release lever (1) and pull out the power supply unit in the direction of the arrow (2). Grip the handle while pulling the power supply.

VCAUTION!

Release your hands from lever (1) as soon as the power supply unit has been pulled out a few centimeters.

ÊCompletely remove the defective power supply unit from the slot.

VCAUTION!

Never leave the slot for the power supply unit empty for more than two minutes during operation. Otherwise, excessive temperatures could damage system components.

88

Operating Manual

RX600 S6

Image 88

Fujitsu RX600 S6 manual CSS components Replacing a hot-plug power supply unit, Vcaution

Contents

Primergy RX600 S6 Server Comments… Suggestions… Corrections… Certified documentation according to DIN EN ISO For your safety High safety useRadio interference Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Preface Further sources of information Features Customer Self Service CSS Battery Backup Units Accessible drives/componentsPreface System board Hot-plug PCI slots Cooling Power supplyHigh level of availability and data security Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Preface ServerView Installation Manager Service and support Preface ServerView Remote Management Electrical data hot-plug power supply unit Technical dataNotational conventions Compliance with regulations and standards Preface Dimensions / Weight Ventilation clearanceAmbient conditions Noise level Overview of the installation steps Overview of the installation steps Safety instructions Important information Installation and operation Important information Before starting up Important information Important information Batteries RX600 S6 Laser information Never remove parts of the optical drive casing ESD label CE conformity Important information Other important information FCC Class a Compliance Statement Transporting the server Operating Manual Environmental protection Environmentally-friendly product design and developmentEnergy-saving information Packaging information Important information Labels on plastic casing parts Returns, recycling and disposal Minimum acclimatization time Hours Hardware installation Unpacking the server Rack system requirements Rack installation/removal of serverFujitsu rack systems 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connecting devices to the server Connectors on the front Connecting the monitor Connectors on the rear Connecting the server to the mains Installation requirementsInstallation requirements for AC redundant configurations PSU Configuration Max. DC Loading DC Redundancy +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Hardware installation Control elements and indicators Front of server Starting up and operation ID card Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Global Error indicator and CSS indicator Rear of server Starting up and operation Starting up and operation ID indicator and button ID indicator LAN Indicators on the hot-plug power supply units Indicators on the power supply units Starting up and operation Switching the server on Switching the server on and offStarting up for the first time Starting up and operation System already installed Switching the server offTimer-controlled switch-on/off Ring indicator IRMC S2 Configuring the server Configuring the SAS/SATA RAID controller card Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Mechanical access protection Bios Setup security functions Property and data protection Power-on indicator remains unlit Server switches itself offPower cable incorrectly connected Server Management has detected an error Screen remains blank No screen display or display drifts Flickering stripes on monitor screenMonitor does not support the set horizontal frequency Drives reported as dead when starting system RAID controller configuration incorrectRAID controller is not configured for this drive Incorrect date and time Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug power supply units Hot-plug components CSS components Replacing a hot-plug power supply unit Vcaution Adding a hot-plug power supply unit Removing a PSU dummy module CSS components Hot-plug fans Identifying the defective CSS component CSS components Replacing a defective fan Unlocking a fan module and removing it CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module Modules on CSS components Removing/installing the dummy module Removing/installing the 2.5-inch dummy module CSS components Installing the HDD/SSD module Unlocking the 2.5-inch HDD/SSD module Installing the 2.5-inch HDD/SSD module Removing the HDD/SSD module CSS components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality CSS components Identifying the defective CSS component Removing a hot-plug expansion card Removing an expansion card from the removal tool Removing the expansion card from the removal tool CSS components Removing engaging hooks Removing engaging hooks from the removal tool CSS components Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards CSS components Identifying the defective memory Open the server see Opening the server on CSS components Removing the memory board in question Removing a defective memory module Removing a memory module CSS components Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Operating Manual 115 Non-hot-plug components Replacing a non-hot-plug expansion card Identifying the defective CSS componentRemoving a non-hot-plug expansion card CSS components Installing a non-hot-plug expansion card Inserting the new expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening/Closing the server Opening the server Opening the server Placing the housing cover Closing the server 128 Operating Manual Memory Modules Configuration Processor Onboard or integrated controllers Appendix server specification InterfacesSlots Drive bays General system informationOperating Panel At system rear side Dimensions Base unit specific Appendix server specificationEnvironmental Electrical values 134 Operating Manual