3.1 HDD/SSD module and dummy module, Modules on | Fujitsu RX600 S6

CSS components

●Always set the HDD/SSD module down carefully, with the large surface facing downwards to prevent it from tipping over.

8.1.3.1HDD/SSD module and dummy module

Figure 18: 2.5-inch HDD module and dummy module

1	Dummy module

2	Tabs for unlocking the dummy module

3	HDD/SSD module (installation frame with hard disk drive or solid state
	disk installed)

4	Indicators:
	HDD/SSD Busy (LED green)
	HDD/SSD Fault (LED orange)
	For description see section "Indicators on the hot-plug HDD/SSD
	modules" on page 62.
5	Handle for locking and unlocking the HDD/SSD module

6	Button for locking and unlocking the handle

7	Ridge for applying a sticker with the current drive name and drive size

96

Operating Manual

RX600 S6

Image 96

Fujitsu RX600 S6 manual 3.1 HDD/SSD module and dummy module, Modules on

Contents

Primergy RX600 S6 Server Comments… Suggestions… Corrections… Certified documentation according to DIN EN ISO For your safety High safety useRadio interference Aluminum electrolytic capacitors Measures against momentary voltage drop Harmonic Current StandardsOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Preface Further sources of information Features Customer Self Service CSS Battery Backup Units Accessible drives/componentsPreface System board Hot-plug PCI slots Power supply CoolingHigh level of availability and data security Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Preface ServerView Installation Manager Service and support Preface ServerView Remote Management Technical data Electrical data hot-plug power supply unitNotational conventions Compliance with regulations and standards Preface Dimensions / Weight Ventilation clearanceAmbient conditions Noise level Overview of the installation steps Overview of the installation steps Safety instructions Important information Installation and operation Important information Before starting up Important information Important information Batteries RX600 S6 Laser information Never remove parts of the optical drive casing ESD label CE conformity Important information Other important information FCC Class a Compliance Statement Transporting the server Operating Manual Environmental protection Environmentally-friendly product design and developmentEnergy-saving information Packaging information Important information Labels on plastic casing parts Returns, recycling and disposal Minimum acclimatization time Hours Hardware installation Unpacking the server Rack installation/removal of server Rack system requirementsFujitsu rack systems 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connecting devices to the server Connectors on the front Connecting the monitor Connectors on the rear Connecting the server to the mains Installation requirementsInstallation requirements for AC redundant configurations PSU Configuration Max. DC Loading DC Redundancy +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Hardware installation Control elements and indicators Front of server Starting up and operation ID card Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Global Error indicator and CSS indicator Rear of server Starting up and operation Starting up and operation ID indicator and button ID indicator LAN Indicators on the hot-plug power supply units Indicators on the power supply units Starting up and operation Switching the server on and off Switching the server onStarting up for the first time Starting up and operation System already installed Switching the server offTimer-controlled switch-on/off Ring indicator IRMC S2 Configuring the server Configuring the SAS/SATA RAID controller card Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Mechanical access protection Bios Setup security functions Property and data protection Power-on indicator remains unlit Server switches itself offPower cable incorrectly connected Server Management has detected an error Screen remains blank Flickering stripes on monitor screen No screen display or display driftsMonitor does not support the set horizontal frequency Drives reported as dead when starting system RAID controller configuration incorrectRAID controller is not configured for this drive Incorrect date and time Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug power supply units Hot-plug components CSS components Replacing a hot-plug power supply unit Vcaution Adding a hot-plug power supply unit Removing a PSU dummy module CSS components Hot-plug fans Identifying the defective CSS component CSS components Replacing a defective fan Unlocking a fan module and removing it CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module Modules on CSS components Removing/installing the dummy module Removing/installing the 2.5-inch dummy module CSS components Installing the HDD/SSD module Unlocking the 2.5-inch HDD/SSD module Installing the 2.5-inch HDD/SSD module Removing the HDD/SSD module CSS components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality CSS components Identifying the defective CSS component Removing a hot-plug expansion card Removing an expansion card from the removal tool Removing the expansion card from the removal tool CSS components Removing engaging hooks Removing engaging hooks from the removal tool CSS components Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards CSS components Identifying the defective memory Open the server see Opening the server on CSS components Removing the memory board in question Removing a defective memory module Removing a memory module CSS components Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Operating Manual 115 Non-hot-plug components Identifying the defective CSS component Replacing a non-hot-plug expansion cardRemoving a non-hot-plug expansion card CSS components Installing a non-hot-plug expansion card Inserting the new expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening/Closing the server Opening the server Opening the server Placing the housing cover Closing the server 128 Operating Manual Memory Modules Configuration Processor Appendix server specification Interfaces Onboard or integrated controllersSlots Drive bays General system informationOperating Panel At system rear side Appendix server specification Dimensions Base unit specificEnvironmental Electrical values 134 Operating Manual