Hot-plug components, Hot-plug power supply units | Fujitsu RX600 S6

CSS components

8.1Hot-plug components

This section describes how to handle hot-plug components and how to modify your server hardware (e.g. adding/replacing hot-plug power supply units).

The hot-plug procedure increases the availability of system operation and guarantees a high degree of data integrity and failsafe performance.

8.1.1Hot-plug power supply units

The server must have at least two hot-plug power supply units (PSUs) to ensure redundant power supply. If one power supply unit fails, the other unit ensures that the operation can continue uninterrupted. The defective power supply unit can be replaced during operation (hot-plug).

VCAUTION!

●Areas around the power supply unit may remain extremely hot after shutdown. Wait for a while after shutdown before removing the power supply unit.

●When installing the power supply unit, be sure to confirm that the connector of the PSU is not damaged or bent.

●Do not insert your hands in the power supply unit slot when removing the power supply unit. Doing so may cause electric shock.

●If the power supply unit is hard to remove, do not pull out it by force.

●The power supply unit is heavy, so handle it carefully. If you drop it by mistake, injuries may result.

RX600 S6

Operating Manual

87

Image 87

Fujitsu RX600 S6 manual Hot-plug components, Hot-plug power supply units

Contents

Primergy RX600 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections… Aluminum electrolytic capacitors For your safetyHigh safety use Radio interference Measures against momentary voltage drop Harmonic Current StandardsOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Non-hot-plug components Opening/Closing the server Concept and target groups for this manual Preface Preface Documentation overview Further sources of information Customer Self Service CSS Features Hot-plug PCI slots Battery Backup UnitsAccessible drives/components Preface System board Power supply CoolingHigh level of availability and data security Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation Manager Preface ServerView Remote Management Technical data Electrical data hot-plug power supply unitNotational conventions Compliance with regulations and standards Noise level Preface Dimensions / WeightVentilation clearance Ambient conditions Overview of the installation steps Overview of the installation steps Important information Safety instructions Important information Before starting up Installation and operation Important information Important information Batteries RX600 S6 Never remove parts of the optical drive casing Laser information ESD label Important information Other important information CE conformity FCC Class a Compliance Statement Transporting the server Operating Manual Packaging information Environmental protectionEnvironmentally-friendly product design and development Energy-saving information Returns, recycling and disposal Important information Labels on plastic casing parts Hours Minimum acclimatization time Unpacking the server Hardware installation Rack installation/removal of server Rack system requirementsFujitsu rack systems 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connectors on the front Connecting devices to the server Connectors on the rear Connecting the monitor PSU Configuration Max. DC Loading DC Redundancy Connecting the server to the mainsInstallation requirements Installation requirements for AC redundant configurations +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Cable clamps to secure the power cords Connecting the power cord Disconnecting cables Connecting cables Hardware installation Front of server Control elements and indicators ID card Starting up and operation Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Rear of server Global Error indicator and CSS indicator Starting up and operation ID indicator Starting up and operation ID indicator and button LAN Indicators on the power supply units Indicators on the hot-plug power supply units Starting up and operation Switching the server on and off Switching the server onStarting up for the first time Ring indicator Starting up and operation System already installedSwitching the server off Timer-controlled switch-on/off IRMC S2 Configuring the SAS/SATA RAID controller card Configuring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Bios Setup security functions Mechanical access protection Property and data protection Server Management has detected an error Power-on indicator remains unlitServer switches itself off Power cable incorrectly connected Screen remains blank Flickering stripes on monitor screen No screen display or display driftsMonitor does not support the set horizontal frequency Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect RAID controller is not configured for this drive Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug components Hot-plug power supply units Vcaution CSS components Replacing a hot-plug power supply unit Removing a PSU dummy module Adding a hot-plug power supply unit CSS components Identifying the defective CSS component Hot-plug fans Unlocking a fan module and removing it CSS components Replacing a defective fan CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules Modules on 3.1 HDD/SSD module and dummy module Removing/installing the 2.5-inch dummy module CSS components Removing/installing the dummy module Unlocking the 2.5-inch HDD/SSD module CSS components Installing the HDD/SSD module Removing the HDD/SSD module Installing the 2.5-inch HDD/SSD module CSS components Hot-plug expansion cards PCI slots with and without hot-plug functionality Slot # Description Removing a hot-plug expansion card CSS components Identifying the defective CSS component Removing the expansion card from the removal tool Removing an expansion card from the removal tool Removing engaging hooks from the removal tool CSS components Removing engaging hooks Removing the retaining plate from the removal tool CSS components Removing a dummy module Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards Open the server see Opening the server on CSS components Identifying the defective memory Removing a defective memory module CSS components Removing the memory board in question Removing a memory module Reinstalling the memory board in question CSS components Installing a new memory module Removing the memory air baffle to add a memory board Adding a memory board Operating Manual 115 Non-hot-plug components Identifying the defective CSS component Replacing a non-hot-plug expansion cardRemoving a non-hot-plug expansion card Inserting the new expansion card CSS components Installing a non-hot-plug expansion card Removing an SFP+ transceiver module Replacing SFP+ transceiver modules Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening the server Opening/Closing the server Opening the server Closing the server Placing the housing cover 128 Operating Manual Processor Memory Modules Configuration Appendix server specification Interfaces Onboard or integrated controllersSlots At system rear side Drive baysGeneral system information Operating Panel Appendix server specification Dimensions Base unit specificEnvironmental Electrical values 134 Operating Manual