Opening/Closing the server, Opening the server | Fujitsu RX600 S6

CSS components

8.3Opening/Closing the server

VCAUTION!

The actions described in this section may only be performed by personnel with the appropriate technical training. (The device can be seriously damaged if it is opened without authorization or if repairs are attempted by untrained personnel.)

8.3.1Opening the server

VCAUTION!

●The server can be seriously damaged if it is opened without authorization or if repairs are attempted by untrained personnel.

●It is essential to observe the safety instructions in chapter "Important information" on page 27.

●Before removing or attaching covers, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the outlet. Failure to do so can cause electric shock.

●The housing cover must be replaced as soon as possible for purposes of cooling, to comply with EMC regulations (regulations regarding electromagnetic compatibility) and to prevent fires. The housing cover must not remain open for longer than 5 minutes.

●Use the anti-tilt plate to prevent the rack from tipping when installing the rack. Pulling the server out of the rack without having installed the anti-tilt plate may cause the rack to tip over.

●Be careful not to pinch fingers or clothes when sliding out the server or pushing it back. Failure to do so may cause injury.

RX600 S6

Operating Manual

125

Image 125

Fujitsu RX600 S6 manual Opening/Closing the server, Opening the server

Contents

Primergy RX600 S6 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections… High safety use For your safetyRadio interference Aluminum electrolytic capacitors Only for the Japanese market About Sata hard disk drives Measures against momentary voltage dropHarmonic Current Standards Only for the Japanese market Operating Manual Contents Control elements and indicators Contents Non-hot-plug components Opening/Closing the server Concept and target groups for this manual Preface Preface Documentation overview Further sources of information Customer Self Service CSS Features Accessible drives/components Battery Backup UnitsPreface System board Hot-plug PCI slots High level of availability and data security Power supplyCooling Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Service and support Preface ServerView Installation Manager Preface ServerView Remote Management Notational conventions Technical dataElectrical data hot-plug power supply unit Compliance with regulations and standards Ventilation clearance Preface Dimensions / WeightAmbient conditions Noise level Overview of the installation steps Overview of the installation steps Important information Safety instructions Important information Before starting up Installation and operation Important information Important information Batteries RX600 S6 Never remove parts of the optical drive casing Laser information ESD label Important information Other important information CE conformity FCC Class a Compliance Statement Transporting the server Operating Manual Environmentally-friendly product design and development Environmental protectionEnergy-saving information Packaging information Returns, recycling and disposal Important information Labels on plastic casing parts Hours Minimum acclimatization time Unpacking the server Hardware installation Fujitsu rack systems Rack installation/removal of serverRack system requirements 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connectors on the front Connecting devices to the server Connectors on the rear Connecting the monitor Installation requirements Connecting the server to the mainsInstallation requirements for AC redundant configurations PSU Configuration Max. DC Loading DC Redundancy +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Cable clamps to secure the power cords Connecting the power cord Disconnecting cables Connecting cables Hardware installation Front of server Control elements and indicators ID card Starting up and operation Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Rear of server Global Error indicator and CSS indicator Starting up and operation ID indicator Starting up and operation ID indicator and button LAN Indicators on the power supply units Indicators on the hot-plug power supply units Starting up and operation Starting up for the first time Switching the server on and offSwitching the server on Switching the server off Starting up and operation System already installedTimer-controlled switch-on/off Ring indicator IRMC S2 Configuring the SAS/SATA RAID controller card Configuring the server Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Bios Setup security functions Mechanical access protection Property and data protection Server switches itself off Power-on indicator remains unlitPower cable incorrectly connected Server Management has detected an error Screen remains blank Monitor does not support the set horizontal frequency Flickering stripes on monitor screenNo screen display or display drifts RAID controller configuration incorrect Drives reported as dead when starting systemRAID controller is not configured for this drive Incorrect date and time Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug components Hot-plug power supply units Vcaution CSS components Replacing a hot-plug power supply unit Removing a PSU dummy module Adding a hot-plug power supply unit CSS components Identifying the defective CSS component Hot-plug fans Unlocking a fan module and removing it CSS components Replacing a defective fan CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules Modules on 3.1 HDD/SSD module and dummy module Removing/installing the 2.5-inch dummy module CSS components Removing/installing the dummy module Unlocking the 2.5-inch HDD/SSD module CSS components Installing the HDD/SSD module Removing the HDD/SSD module Installing the 2.5-inch HDD/SSD module CSS components Hot-plug expansion cards PCI slots with and without hot-plug functionality Slot # Description Removing a hot-plug expansion card CSS components Identifying the defective CSS component Removing the expansion card from the removal tool Removing an expansion card from the removal tool Removing engaging hooks from the removal tool CSS components Removing engaging hooks Removing the retaining plate from the removal tool CSS components Removing a dummy module Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards Open the server see Opening the server on CSS components Identifying the defective memory Removing a defective memory module CSS components Removing the memory board in question Removing a memory module Reinstalling the memory board in question CSS components Installing a new memory module Removing the memory air baffle to add a memory board Adding a memory board Operating Manual 115 Non-hot-plug components Removing a non-hot-plug expansion card Identifying the defective CSS componentReplacing a non-hot-plug expansion card Inserting the new expansion card CSS components Installing a non-hot-plug expansion card Removing an SFP+ transceiver module Replacing SFP+ transceiver modules Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening the server Opening/Closing the server Opening the server Closing the server Placing the housing cover 128 Operating Manual Processor Memory Modules Configuration Slots Appendix server specification InterfacesOnboard or integrated controllers General system information Drive baysOperating Panel At system rear side Environmental Appendix server specificationDimensions Base unit specific Electrical values 134 Operating Manual