Manuals / Fujitsu / Computer Equipment / Server

Fujitsu RX600 S6 manual Incorrect date and time, Drives reported as dead when starting system

Models: RX600 S6

1 134

Download 134 pages 57.82 Kb

Page 82

Troubleshooting and tips

7.6Incorrect date and time

ÊSet the date and time in the operating system or in the BIOS Setup under the Main menu, using System Date and System Time respectively.

INote that the operating system may affect the system time. For example, the operating system time may deviate from the system time under Linux, and would overwrite the system time in the default setting on shutdown.

If the date and time are still wrong after the server has been switched off and back on again, replace the lithium battery (for a description refer to the "System Board D3141 for PRIMERGY RX600 S6 Technical Manual") or contact our customer service team.

7.7Drives reported as "dead" when starting system

RAID controller configuration incorrect

ÊCheck and correct the settings for the drives using the RAID controller utility. Further information is provided in the manual for the RAID controller.

7.8Added drive reported as defective

RAID controller is not configured for this drive

The drive was probably installed when the system was switched off.

ÊReconfigure the RAID controller for the drive using the corresponding utility. Information is provided in the documentation for the RAID controller.

or

ÊRemove and reinstall the drive while the system is switched ON.

If the drive continues to be shown as defective, then replace it (see "Hot-plug HDD/SSD modules" on page 94).

82

Operating Manual

RX600 S6

Image 82

Fujitsu RX600 S6 Incorrect date and time, Drives reported as dead when starting system, Added drive reported as defective

Contents

Primergy RX600 S6 Server Comments… Suggestions… Corrections… Certified documentation according to DIN EN ISO Radio interference For your safetyHigh safety use Aluminum electrolytic capacitors Harmonic Current Standards Measures against momentary voltage dropOnly for the Japanese market About Sata hard disk drives Only for the Japanese market Operating Manual Contents Contents Control elements and indicators Non-hot-plug components Opening/Closing the server Preface Concept and target groups for this manual Documentation overview Preface Further sources of information Features Customer Self Service CSS Preface System board Battery Backup UnitsAccessible drives/components Hot-plug PCI slots Cooling Power supplyHigh level of availability and data security Preface Preface IRMC S2 with integrated management LAN connector Preface Server management Preface ServerView Installation Manager Service and support Preface ServerView Remote Management Electrical data hot-plug power supply unit Technical dataNotational conventions Compliance with regulations and standards Ambient conditions Preface Dimensions / WeightVentilation clearance Noise level Overview of the installation steps Overview of the installation steps Safety instructions Important information Installation and operation Important information Before starting up Important information Important information Batteries RX600 S6 Laser information Never remove parts of the optical drive casing ESD label CE conformity Important information Other important information FCC Class a Compliance Statement Transporting the server Operating Manual Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging information Important information Labels on plastic casing parts Returns, recycling and disposal Minimum acclimatization time Hours Hardware installation Unpacking the server Rack system requirements Rack installation/removal of serverFujitsu rack systems 3rd party racks Mechanical requirements RX600 S6 Mounting the server into the rack Connecting devices to the server Connectors on the front Connecting the monitor Connectors on the rear Installation requirements for AC redundant configurations Connecting the server to the mainsInstallation requirements PSU Configuration Max. DC Loading DC Redundancy +1 2 PSUs 830W Yes +1 3 PSUs 1580W +1 4 PSUs 2320W Installation in PRIMECENTER/Datacenter rack Side wall designated by the symbol Operating Manual Photo shows installation of a protective earth conductor Connecting the power cord Cable clamps to secure the power cords Connecting cables Disconnecting cables Hardware installation Control elements and indicators Front of server Starting up and operation ID card Starting up and operation Control elements Starting up and operation Indicators on the control panel ServerView Local Service Display Indicators on a hot-plug HDD/SSDmodule Global Error indicator and CSS indicator Rear of server Starting up and operation Starting up and operation ID indicator and button ID indicator LAN Indicators on the hot-plug power supply units Indicators on the power supply units Starting up and operation Switching the server on Switching the server on and offStarting up for the first time Timer-controlled switch-on/off Starting up and operation System already installedSwitching the server off Ring indicator IRMC S2 Configuring the server Configuring the SAS/SATA RAID controller card Advantages of the ServerView Installation Manager Installing the operating system Cleaning the server Starting up and operation Mechanical access protection Bios Setup security functions Property and data protection Power cable incorrectly connected Power-on indicator remains unlitServer switches itself off Server Management has detected an error Screen remains blank No screen display or display drifts Flickering stripes on monitor screenMonitor does not support the set horizontal frequency RAID controller is not configured for this drive Drives reported as dead when starting systemRAID controller configuration incorrect Incorrect date and time Error message on screen Troubleshooting and tips CSS components CSS components Hot-plug power supply units Hot-plug components CSS components Replacing a hot-plug power supply unit Vcaution Adding a hot-plug power supply unit Removing a PSU dummy module CSS components Hot-plug fans Identifying the defective CSS component CSS components Replacing a defective fan Unlocking a fan module and removing it CSS components Adding new fans Hot-plug HDD/SSD modules Handling drives and HDD/SSD modules 3.1 HDD/SSD module and dummy module Modules on CSS components Removing/installing the dummy module Removing/installing the 2.5-inch dummy module CSS components Installing the HDD/SSD module Unlocking the 2.5-inch HDD/SSD module Installing the 2.5-inch HDD/SSD module Removing the HDD/SSD module CSS components Hot-plug expansion cards Slot # Description PCI slots with and without hot-plug functionality CSS components Identifying the defective CSS component Removing a hot-plug expansion card Removing an expansion card from the removal tool Removing the expansion card from the removal tool CSS components Removing engaging hooks Removing engaging hooks from the removal tool CSS components Removing a dummy module Removing the retaining plate from the removal tool Operating Manual 107 CSS components Operating the expansion card Hot-plug memory boards CSS components Identifying the defective memory Open the server see Opening the server on CSS components Removing the memory board in question Removing a defective memory module Removing a memory module CSS components Installing a new memory module Reinstalling the memory board in question Adding a memory board Removing the memory air baffle to add a memory board Operating Manual 115 Non-hot-plug components Replacing a non-hot-plug expansion card Identifying the defective CSS componentRemoving a non-hot-plug expansion card CSS components Installing a non-hot-plug expansion card Inserting the new expansion card Replacing SFP+ transceiver modules Removing an SFP+ transceiver module Unlatching the locking bail Installing SFP+ transceiver modules Inserting the SFP+ transreiver Carefully fold up and latch the locking bail Installing the secondary SFP+ transceiver module Opening/Closing the server Opening the server Opening the server Placing the housing cover Closing the server 128 Operating Manual Memory Modules Configuration Processor Onboard or integrated controllers Appendix server specification InterfacesSlots Operating Panel Drive baysGeneral system information At system rear side Dimensions Base unit specific Appendix server specificationEnvironmental Electrical values 134 Operating Manual