Control Panel and Knobs

It’s a good idea to wipe the control panel after each use. Clean with mild soap and water or vinegar and water, rinse with clean water and polish dry with a soft cloth.

Do not use abrasive cleansers, strong liquid cleansers, plastic scouring pads or oven cleaners on the control panel—they will damage the finish. A 50/50 solution of vinegar and hot water works well.

The control knobs may be removed for easier cleaning.

Before removing the knobs for cleaning, please note that the knobs on the left side and the knobs on the right side are in the proper OFF position. When replacing the knobs, check the OFF position to insure proper placement.

To remove a knob, pull it straight off the stem. If a knob is difficult to remove, place a thin cloth (like a handkerchief) or a piece of string under and around the knob edge and pull up.

Wash the knobs in soap and water but do not soak. Avoid getting water down in to the knob stem holes.

Painted Surfaces

Painted surfaces include the control panel. Clean these with soap and water or a vinegar and water solution.

Do not use commercial oven cleaners, cleansing powders, steel wool or harsh abrasives on any painted surface.

Glass Surfaces

To clean the outside glass finish, use a glass cleaner. Rinse and polish with a dry cloth. Do not allow the water or cleaner to run down inside openings in the top of the oven door while cleaning.

Care and

Oven Light Replacement

CAUTION: Before replacing your oven light bulb, disconnect the electrical power for your range at the main fuse or circuit breaker panel.

Be sure to let the light cover and bulb cool completely before removing or replacing them. When in use, light bulbs can become warm enough to break if touched with a moist cloth or towel. When cleaning, avoid touching warm lights with cleaning cloths if the light cover is removed.

The oven light bulb is covered with a removable glass cover which is held in place with a wire. Remove the oven door, if desired, to reach the cover easily.

To remove:

Hold your hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover.

DO NOT REMOVE ANY SCREWS TO REMOVE THE COVER.

Replace bulb with 40-watt home appliance bulb.

To replace cover:

Place it into the groove of the light receptacle. Pull the wire forward to the center of cover until it snaps in place. When in place, the wire holds the cover firmly. Be certain the wire is in the depression in the center of the cover.

Connect the electrical power to the range.

Wire cover holder

(continued next page)

Cleaning

23

Page 23
Image 23
GE JMS10 warranty Care, Cleaning

JMS10 specifications

The GE JMS10 is a remarkable jet engine that has garnered attention for its advanced technology and exceptional performance. Designed and manufactured by General Electric, the JMS10 is part of the company’s punctual commitment to fostering innovation in aviation technology. This engine is primarily utilized in regional and business jets, making it a critical component for many modern aircraft.

One of the standout features of the GE JMS10 is its impressive thrust-to-weight ratio. This allows for not only enhanced performance capabilities during takeoff and climb but also improved fuel efficiency during cruise. The engine produces a thrust range typically around 10,000 pounds, making it suitable for various aircraft configurations. The balance between power and efficiency is achieved through the incorporation of advanced materials and cutting-edge design strategies.

The JMS10 is equipped with a high bypass ratio, which significantly contributes to its fuel efficiency. This feature ensures that a larger volume of air bypasses the engine core compared to previous generations, resulting in quieter operation and lower specific fuel consumption. In an era where environmental concerns are paramount, this engine stands out by adhering to stringent noise regulations and reducing carbon emissions.

In terms of technology, the JMS10 employs state-of-the-art digital engine controls. This system optimizes engine performance by continuously monitoring and adjusting conditions in real time, ultimately enhancing reliability and efficiency. Additionally, the engine utilizes advanced aerodynamic designs and premium composites, which contribute to weight savings and overall performance enhancement.

Another characteristic of the GE JMS10 is its focus on maintainability and longevity. The design incorporates modular components, allowing for easier maintenance and reduced downtime during service. This advantage is crucial for airlines and operators looking to optimize their fleet operations while minimizing operational costs.

The GE JMS10 also benefits from robust testing and certification processes, ensuring that it meets or exceeds industry standards for safety and reliability. This dedication to quality provides operators with peace of mind when relying on this engine for their aviation needs.

In summary, the GE JMS10 is a trailblazer in the realm of jet engines, characterized by its excellent thrust-to-weight ratio, high bypass ratio, advanced digital controls, and emphasis on maintainability. Its innovative technologies not only enhance performance but also align with the industry's growing emphasis on sustainability. As the aviation sector continues to evolve, the JMS10 is poised to be at the forefront of next-generation engines, setting new benchmarks for efficiency and environmental responsibility.