CUSTOM PANEL DIMENSIONS
|
| Custom Panel Dimensions | ||||
|
|
|
|
| 42" | |
Custom Door Panel Dimensions |
| ZISW42D (white dispenser) | ||||
| Using Trim Kit ZKT42 |
| ZISB42D (black dispenser) | |||
3/4" thick panel with standard handle | • | The ZKT42 trim kit provides for the installation of 3/4" | ||||
and/or ZWCD1 custom collar trim | ||||||
|
|
|
| custom door and grille panels, using the standard full- | ||
|
|
|
| length handle. Cut panels to size and install. | ||
|
|
| • | For standard dispenser trim: Cut panels to size, rout the | ||
Freezer Panel | Freezer Panel |
|
| bottom of the upper freezer panel and the top of the | ||
Standard | Custom | Fresh Food |
| lower freezer panel to allow placement of support | ||
Dispenser | Dispenser |
| brackets and install (see detail A). | |||
Panel |
| |||||
|
|
| ||||
|
|
| • | For custom dispenser trim ZWCD1 kit must be used: Cut | ||
16 11/16" | 17 11/16" |
|
| panels to size, refer to detail B for dispenser cutout | ||
|
| routing instructions and install. When a raised panel | ||||
|
|
|
| design is used, a custom middle rail is required. A | ||
|
|
|
| |||
| 67 15/16" |
|
| custom collar trim must be located within the raised | ||
|
|
| portion of the panel. This area must be 3/4" thick. See | |||
|
|
|
| |||
| 2 5/16" |
|
| detail C for raised panel design requirements. | ||
|
|
|
|
|
| |
37" |
|
|
|
| Custom Grille Panel | |
|
|
|
|
| 41 1/2" | |
|
|
|
|
|
| |
|
|
|
| A | Over 1/4" Thick (3/4" max) Panel | |
15 1/16" |
| 25 1/16" |
| Grille Panel height can vary to fill installation | ||
|
|
|
| |||
| Important: Maximum weight for fresh food panels is |
| height. |
| ||
|
|
| Installation Height | Dimension A | ||
Detail A | 50 pounds and 30 pounds for freezer door panels. |
|
| 83" | ||
|
|
|
| |||
|
|
|
| |||
Upper |
|
|
|
| ||
Freezer | Detail B Custom |
|
|
| 84" | |
Panel | Dispenser Cutout |
|
|
| ||
|
|
|
| |||
|
|
|
|
| ||
|
|
|
| Important: Maintain | ||
1" | 9 7/16" |
|
| top of doors and bottom of grille panel. | ||
3/32" |
| 7/8" |
|
|
|
|
|
|
|
|
| Detail C | |
| 12 5/16" | Wide |
|
|
| |
|
|
| Raised Panel Design | |||
1" | Rout |
|
| |||
|
|
|
|
| ||
Panel |
|
|
| *3" Stiles |
| |
|
|
| Left Side | Right Side | ||
Face | The Cutout is 9 7/16" wide |
|
| A |
| |
|
|
|
| |||
| by 12 5/16" high. 3/4" panels |
|
| Hole is Cut | ||
|
|
|
| |||
Lower | must be routed on all four |
|
|
| After Door | |
Freezer | sides of the cutout. Rout |
|
|
| Fabrication | |
Panel | the back side of the panel |
|
|
|
| |
| 1/4" deep. 7/8" wide |
|
|
|
|
|
| (shaded area). |
|
|
| A | 14 1/2" |
|
|
|
|
|
| Wide |
|
|
|
|
|
| Middle |
|
|
|
|
|
| Rail |
|
|
|
|
|
| Handle |
|
|
|
|
|
| Side |
*Custom Stiles and | Section AA |
Middle Rail Required |
|
12
