GE Monogram ZIS42N installation instructions ZISW42D white dispenser, ZISB42D black dispenser

CUSTOM PANEL DIMENSIONS

						Custom Panel Dimensions
							42" Built-In Refrigerator
						ZISW42D (white dispenser)
		Front View				ZISB42D (black dispenser)
Side View		(not to scale)
						Design Information
(not to scale)		41" Case Width
						Cutout dimensions, clearances and side panel sizes are
24 3/4"		42" Overall Width
						determined by the many installation options available. Side
					12 1/4" max	panels must be used whenever the sides of the refrigerator
					10-3/4" min	will be exposed. Side panels are not required when
						refrigerator is installed into an enclosure or between pantry
						and oven cabinets. IMPORTANT–Side panels, 1/2" min.
						thick, are required for FRAMELESS CABINETS.
						•	Field installed custom panels, Lexan® or stainless steel
							panels are required. Custom door panels and grille panel
					84 1/2" max		sizes vary to accommodate the kit being used.
						•	A custom toekick can be installed to match or comple-
					83" min
							ment the surrounding cabinetry. Use supplied toekick as
					72 1/4"		a template to cut notches for hinges and water lines.
						Optional Kits:
						•	ZWBP42D: Black Lexan® Panel Kit (no trim kit required).
						•	ZWWP42D: White Lexan® Panel Kit (no trim kit required).
						•	ZWSP42D: Stainless Steel Panel Kit (no trim kit required).
						•	ZKH1: For installation of custom handles on 1/4" panels.
						•	ZKT42: For installation of 3/4" custom panels.
						•	ZKHT1: For installation of custom handles on 3/4" panels.
							(This kit must be used in combination with ZKT42.)
4"						•	ZWCD1: For installation of a custom collar trim on the
							dispenser for one continuous custom panel
		*Finished Width					on the freezer door.
						•	ZKHSS1: Tubular Stainless Steel handles on 1/4" panels.
					Wall View
						•	ZKHTSS1: Tubular Stainless Steel handles on 3/4" panels.
					(not to Scale)
							(This kit must be used in combination with ZKT42.)
		7"				•	ZG2: 1/4" grille panel frame side pieces for 83", 83-1/2" and
			5"				84-1/2" installation heights. Factory set height is 84".
Locate Grounded						•	ZWT1: White toekick (supplied toekick is black). Includes
							a white toekick to fit 36", 42", 48" side-by-side models and
	Electrical outlet		18 3/8"
	Within Solid						36" bottom mount and single door models.
84 1/2" max	Area Above				74" From	Additional Specifications
83-1/4" min					Floor to
						•	A 115 volt 60 Hz., 15 or 20 amp power supply is required.
Finished					Bottom of
Opening					Electrical Area		An individual properly grounded branch circuit or circuit
							breaker is recommended. Install a properly grounded
		Locate Water					3-prong electrical receptacle recessed into the back wall.
		Supply Within					Electrical must be located on rear wall.
		the Shaded				•	Water line can enter opening through the floor or back
	5"	Area Below		5"	3 1/2"		wall. The water line should be 1/4" O.D. copper tubing
							between the cold water line and water connection
							location, long enough to extend to the front of the
3 1/2"							refrigerator. Installation of an easily accessible shut off
							valve in the water line is recommended.
*42" Min. for a flush installation into an enclosure.						Clearances
						If the refrigerator is to be installed in a corner:
*41-1/2" Min. for a semi-flush installation into an enclosure.
Note: Additional cutout width may be required when side panels are						•	A 4" min. clearance between the case trim and adjacent
used. Add side panel thickness to the finished cutout to calculate							°
rough-in width. See installation examples on page 4.							wall on both sides of the refrigerator will assure a 90
							door opening and access to all drawers. A 10" clearance
							is required on both sides for removal of pans.

10