Manuals / GE Monogram / Kitchen Appliance / Refrigerator

GE Monogram ZISB42D ZKHTSS1 for 3/4 Panels, Tubulor Stainless Steel Handles, freezer panels

Models: ZISW42D ZISB42D ZIS42N

1 48

Download 48 pages 63.35 Kb

Page 43

Step 1:

Step 1:

Remove

Handles

ZKHTSS1 for 3/4" Panels

Tubulor Stainless Steel Handles

• Open doors to 90°. Remove the screws from the full-length handles of both doors.

• Retain screws, discard handles.

Note: If a custom collar is to be used, order ZWCD1 Trim Kit for 36" and 42" wide models. Order ZWCD2 for 48" wide models.

Step 2:

Match

Handle Extrusions to Panels

•Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.

•Place custom panels on the pad, appearance side down.

Note: If panels are wood, be sure to note which end is the top so that wood grain is in the correct direction on both (or all 3) panels.

•Place new extrusion against the handle side of the panels.

•Align the extrusion evenly with the top and bottom of the panel.

•Follow the same procedure on the opposite panel.

	• Tape the extrusions to the panels to prevent	Freezer
	movement.	Freezer
	movement.	Upper
	• Center punch and drill 1/8" pilot holes through the	Panel
	holes in the extrusion and into the panel.

•Turn panel over. On the appearance side, use 9/32" bit to enlarge clearance hole.

IMPORTANT: Hole locations must be exact to accept handle
IMPORTANT: Hole locations must be exact to accept handle
standoff and handle assembly.
For models with full width dispenser trim and 2 piece	Back
freezer panels:	Back
freezer panels:	Side
• Carefully, align the top of the upper panel and the	Side
• Carefully, align the top of the upper panel and the	Freezer
bottom of the lower panel with extrusion ends.	Lower
	Panel

	Models
	With Full Width
	Dispenser Trim

Top	Note: Be sure to orient
End	extrusions and handles
	correctly. The top ends of
	the extrusions are cutout to fit
	the shape of the top of the
	door.

Align Extrusion

Even With

Panel

Back

Side

Fresh

Food

Panel

Back

Side

Freezer

Panel

Freezer	Fresh Food	ZKHTSS1 INSTALLATION
Extrusion	Extrusion

43

Image 43

GE Monogram ZISB42D, ZIS42N ZKHTSS1 for 3/4 Panels, Tubulor Stainless Steel Handles, freezer panels, Step Remove Handles

Contents

Models ZIS42N ZISW42D ZISB42D GE Monogram 42 Built-In RefrigeratorsCustom Options Guide and Installation Instructions Consulter « Mise à terre du réfrigérateur », page For Monogram local service in your areaCustom Panel Dimensions ATTENTION Cet appareil doit être correctement mis à la terre42 Built-In Refrigerator Design InformationTrue Flush Installation To accomplish an attractive installation, you mustAccessory Panel Kits Installation ExamplesInstallation Between Base Wall Cabinets Installation At End-of-Run3/4 thick custom panels-Without trim kits Design Information42 Built-In Refrigerator You shouldNon-dispenser Custom Panel Dimensions42 Built-In Refrigerator ZIS42N1/4 thick panels Custom Panel Dimensions42 Built-In Refrigerator ZIS42N non-dispenserThe ZKT42 trim kit provides for the installation of 3/4 Custom Panel DimensionsUsing Trim Kit ZKT42 length handle. Cut panels to size and install42 Built-In Refrigerator Custom Panel DimensionsUsing Trim Kits ZKT42 3/4 thick panel with custom handle Custom Door Panel DimensionsZISB42D black dispenser Custom Panel Dimensions42 Built-In Refrigerator ZISW42D white dispenser42 Built-In Refrigerator 1/4 thick panels or Panels secured to 1/4 thick backingCustom Panel Dimensions Custom Door Panel Dimensions Using Standard TrimZISW42D white dispenser Custom Panel DimensionsUsing Trim Kit ZKT42 42 Built-In RefrigeratorZISW42D white dispenser Custom Panel DimensionsUsing Trim Kit ZKT42 42 Built-In RefrigeratorFor All Monogram Built-In Refrigerators Custom Panel DimensionsSide Panel or Filler Options not to scale 42 Built-In RefrigeratorUse of Adapter plug InstallationPRUDENCE 42 Built-In Refrigerator42 Built-In Refrigerator InstallationPRUDENCE PRUDENCEINSTALLATION InstallationStep 2A For Installations With A Reverse Osmosis System Only Skip This Step When Not Using RO System42 Built-In Refrigerator InstallationFor front leveling, use a 1-1/2 open-end wrench OPTION 2 Secure refrigerator at the sides Installation42 Built-In Refrigerator Step OPTION 1 Secure refrigerator at the topTo insert decorative grille panel into the frame InstallationTo raise or lower case trim to other installation heights 42 Built-In RefrigeratorParts List ZKH1 Trim Kit For 1/4 PanelsSupport for Custom Handles Support for Custom Handles ZKH1 Trim Kit For 1/4 Panels3/4 Min 1-1/2 Max Screw ZKH1 INSTALLATIONZKH1 Trim Kit For 1/4 Panels Support for Custom HandlesSupport for Custom Handles ZKH1 Trim Kit For 1/4 PanelsRetain screws, discard handle ZKH1 Trim Kit For 1/4 Panels Option 2 InstallationStep Install custom handle Step Mount assembled dispenser trim Step Install custom handleTo change grille panel size ZG2 Trim KitGrille Panel Frame Adjustment FOR 83, 83-1/2 AND 84-1/2 INSTALLATION HEIGHTS3/4 Custom Panels ZKT42 Trim KitParts List Kit contentsImportant When the bottom and bottom using original screwsor dispenser model using custom collar trim Step Remove InstallZKT42 Trim Kit Dimension B3/4 Custom Panels ZKT42 Trim Kit INSTALLATION ZKT423/4 Custom Panels 3/4 Custom Panels Dimension ADimension B ZKT42 Trim Kit3/4 Custom Panels ZKT42 Trim KitPush the panel back against the steel door Support for Custom Handles ZKHT1 Trim Kit For 3/4 PanelsParts List ZKHT1 INSTALLATIONStep Locate position of handles ZKHT1 Trim Kit For 3/4 PanelsSupport for Custom Handles Step Temporarily mount door panelsSupport for Custom Handles ZKHT1 Trim Kit For 3/4 PanelsDoor Handle Handle Side ZKHT1 Trim Kit For 3/4 PanelsSupport for Custom Handles 1-13/16Support for Custom Handles ZKHT1 Trim Kit For 3/4 PanelsTools and materials required ZKHSS1 for 1/4 PanelsParts List Tubular Stainless Steel HandlesFor models with full width dispenser trim and 2 piece freezer panels ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles FOR CUSTOM WOOD PANELSFOR STAINLESS STEEL PANELS If you are installing these handles onto Stainless Steel panelsZKHSS1 for 1/4 Panels Tubular Stainless Steel HandlesFor Stainless Panels ZKHSS1 for 1/4 PanelsFOR STAINLESS STEEL PANELS Tubular Stainless Steel Handlesor ZKT48 trim kit ZKHTSS1 for 3/4 PanelsParts List Tubulor Stainless Steel HandlesStep Remove Handles ZKHTSS1 for 3/4 PanelsTubulor Stainless Steel Handles freezer panelsTubular Stainless Steel Handles ZKHTSS1 for 3/4 panelsIt is best that 2 people perform this step It is best that 2 people perform this step ZKHTSS1 for 3/4 PanelsTubular Stainless Steel Handles For models with full width dispenser trim and 2 piece freezer panelsParts List ZWCD1 Trim KitCustom Dispenser Collar Cut dispenser hole and rout door panel Install collar brackets and trimZWCD1 Trim Kit Custom Dispenser CollarMonogram