Dimension B | GE Monogram ZISW42D, ZIS42N, ZISB42D guide

ZKT42 Trim Kit

3/4" Custom Panels

Option 1 Installation

Step 3
Apply panel	Dimension A
support brackets	Dimension A

Back Side Door Panel

ZKT42–6-3/4"

Hinge

Support Bracket

Sde

Dimension B

ZKT42–7-7/8"

Bottom Edge

A

Freezer Panels

Support Bracket

Bottom Edge

B

Fresh Food Panel

Step 4 Install panels

• Position support bracket on freezer panel,	• Secure support brackets to the bottom of the panels
dimension A, from the hinge side edge.	with #4 screws provided. Align the brackets flush with
• Position support bracket on fresh food panel,	the bottom of the panels, with tabs protruding below.
dimension B, from the hinge side edge.	• Bracket location measured from the hinge side, is the
	same for panels with custom handles or standard
	handles.

INSTALLATION	ZKT42
ZKT42 – Install 17 screws

•Place the 3/4" panel on the bottom trim with support bracket tabs inserted into slots. Push the panel back against the steel door, making sure panel is flush to hinge side trim.

•Carefully drill starter holes in panel using a small drill bit.

•Attach the panel to the top and hinge side by installing

screws from the back of the trim through the wood panel.

•Follow the same procedure to install fresh food door panel.

•Re-install door handles with original screws.

29

Image 29

GE Monogram ZISW42D, ZIS42N, ZISB42D installation instructions Dimension B

Contents

Models GE Monogram Built-In Refrigerators Consulter « Mise à terre du réfrigérateur », Custom Panel DimensionsDesign Information Trim Kits To accomplish an attractive installation, you must True Flush InstallationDesign Information Built-In Refrigerator Thick Built-In Refrigerators41-1/2 Cabinet Thick custom panels-Without trim kits You should Non-dispenser Custom Panel Dimensions ZIS42N non-dispenser ZKT42 trim kit provides for the installation of 3/4 Using Trim Kit ZKT42 Thick panel with standard handleCustom door and grille panels, using the standard full 67 15/16 Max Freezer Panel ZISB42D black dispenser ZISW42D white dispenser ZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard Trim Lower freezer panel to allow placement of support Length handle. Cut panels to size and installDispenser Brackets and install see detail a Grille Panel height can vary to fill installation Detail B Freezer Rout panels to specification below on 67 15/16 Detail a and installSee detail B Standard Custom Detail B 23 9/16 For All Monogram Built-In Refrigerators24 3/4 Trim Use of Extension Cords InstallationUse of Adapter plug Shut off the main water supply Slide carton off top of cabinetFloor Copper Tubing Washer For Installations With a Reverse Osmosis System Only Side panels must be installed plumbStep Install Side Panels Rotate Clockwise To Remove Filter Bypass Plug Step Install Door Panels To install 1/4 door panelsStep Roll Refrigerator Into Opening Step Level Refrigerator Refrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights ZKH1 Trim Kit For 1/4 Panels Parts ListSupport for Custom Handles Tor door panels. Handles not included. The door Locate position Option 1 Installation Step Extrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion Handle Step Locate Position Handle Re-install dispenser trim, temporarily Assembled Option 2 Installation Step Custom handleDispenser Trim With To change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Trim Models Dimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Install panel support brackets Dimension a Dimension BZKT42-6-3/4 Back Side Freezer Panels Hinge Upper Lower Step Install Handles Step Install Panels Fresh food door extrusion ZKHT1 Trim Kit For 3/4 PanelsFreezer door extrusion Back Side Step Locate position of handles Step Temporarily Mount Door panels Step Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Model using Option 1 InstallationFor dispenser Before Assembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle Tape extrusions to panels to prevent movement Reinstall original screws into the door extrusionSee a For Stainless Raised Panel on 1/4 Thick Backing For Stainless Panels Tubulor Stainless Steel Handles ZKHTSS1 for 3/4 Panels Freezer panels Step Install Assembled Panels Step Install Standoffs onto Handles ZKHTSS1 Custom Dispenser Collar ZWCD1 Trim KitCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16 Select the door panel size for your application Monogram