Honeywell VISTA-10PSIA Field, TITLE and EXPLANATION, Event Log Full Report Code, Option Selection

FIELD	TITLE and EXPLANATION
	Event Log Full Report Code
*89
	Enter the appropriate report code, which is sent when the event log is 80% full (if an event log enable is
	made in field ∗90). If the log becomes full, new messages overwrite the oldest messages in the log.
	Event Log Enables
*90
	Select the types of events (up to 32 events) the system should log. The downloader operator can then
	upload the log and view or print out all or selected categories of the log. The downloader operator can
	also clear the log. The Event log can also be viewed at an alpha keypad. The display/printout at the
	central station will show the date, time, event, and description of occurrences.
	Example: For Alarm/Alarm Restore” and “Open/Close”, enter 9 (1+ 8); to select all events, enter #15.
	Option Selection
*91
	Select the desired options by adding the values of each desired option. Multiple choice example: for both
	AAV and Exit delay restart, enter # + 12 (4 + 8).
						Options: Same as VISTA-10P.
		VISTA-10PSIA:
		Call Waiting Disable: 0 = call waiting not used
	1 =		call waiting disable digits (*70) entered in field *40; (when selected, the system dials the entry
			in field *40 only on alternate dial attempts; this allows proper dialing in the event call waiting
			service is later canceled by the user).
	“Exit Delay Restart/reset” option allows use of the [∗] key to restart the exit delay at any time when the
	system is armed STAY or INSTANT. This feature also enables automatic exit delay reset, which resets
	exit delay if the entry/exit door is re-opened and closed before exit delay time expires after arming
	AWAY. Automatic Exit Delay Reset occurs only once during an armed period.
	IMPORTANT: AAV should not be used when Paging or Alarm Reports are sent to a secondary
	number unless the monitoring zone option is used (which pauses calls). Otherwise, the call to the
	secondary number by the communicator after the alarm report will prevent the AAV from taking
	control of the telephone line, and the AAV “Listen in” session cannot take place.
	UL UL installations using the AAV feature must use the ADEMCO UVCM module (part of
	the ADEMCO UVS system). Exit Delay Restart/Reset must be disabled.
	SIA Guidelines: Exit delay should be enabled.
	No. of Reports In Armed Period per Zone (Swinger Suppression)
*93
	Select the number (0, 1, or 2) of alarm/alarm restore message pairs per zone allowed to be sent to the
	central station in an armed period. SIA Guidelines: Must be set for option 1 or 2.
					: Report Pairs: 1 = 1 report pair; 2 = 2 report pairs
		VISTA-10PSIA
		Unlimited Reports Enable:
	0 =		restrict reports to the setting in entry 1
	1 =		unlimited reports for zones listed in zone list 7; (use zone list 7 to list zones that require unlimited
			reporting; these zones ignore the setting in entry 1)
	Download Phone Number
*94
	Enter the downloading computer phone number.
	Do not fill unused spaces. End field by entering ∗. To clear entries from field, press ∗94∗.
	Ring Count For Downloading
*95
	Refer to the chart below and program this field accordingly.
	phone			answer			down-
	module			machine			loading	Set field ∗95 to…
	yes			no			no	1-14 (not 0)
	yes			yes			no	higher than number of rings set on answer machine (e.g., if ans. machine is 4
								rings, set this field to 5). This allows access to the phone module if the answer
								machine is turned off.
	yes			no			yes	1-14 (not 0)
	yes			yes			yes	15 (bypasses answer machine†)
	no			no			no	0
	no			yes			no	0
	no			no			yes	1-14
	no			yes			yes	15

†NOTE: If “15” is entered to bypass an answering machine, and a 4285 or 4286 Phone Module is included in the system, note the following: When calling in from an off-premises phone, the user should make the initial call, allow 1 or 2 rings only, then hang up, then call again. The phone module will now seize the line, and 2 long tones sound, followed by the usual voice prompt for the access code. If this procedure is not followed, phone module operation will not be possible.

4-7