Parts List | HP 0706124 REV B specs

9.Remove the media spools, which are packed together under the printer module.

Do not remove the printer module from the pallet at this time. The printer rests on two shipping supports. You will use these supports and two assembly supports to help assemble the printer.

Note	Replacement shipping packaging and instructions
	are available from MacDermid ColorSpan Technical
	Services (phone: 800-925-0563).

10.Refer to the following list to verify that you received all of the parts and accessories.

Notify ColorSpan immediately if you are missing any of the components listed below.

Parts List

Main Box	Outside of Box:
	◆ “Watch Me First” CD-ROM
	◆	Unpacking & Assembly Diagram
	◆	Declaration of Conformity

Inside of Box:

◆Printer Module

◆(1) Stand crossbar

◆(2) Media spools with collets

◆(1) Stand leg box

◆(1) Ink tray box

◆(1) Accessory box

Stand Leg Box	◆	(2)	Stand legs

Ink Tray Box	◆	(2)	Ink trays

Accessory Box	◆	(18) Black Phillips head screws
	◆ (4) Silver Phillips head screws
	◆ (2) Red-headed bolts
	◆	(1)	Service station
	◆ (1) Ink maintenance kit: manual priming
		bulb, purge clip, drain bottle
	◆ (1) Fill system assembly
	◆ (2) Spare ink tubes
	◆ (11) Color Map print mode cards
	◆ (1) White point reference chip
	◆	(1)	Screwdriver
	◆	(1)	Hex wrench

◆ (1) VideoNet or Ethernet cable ◆ (3) U.S. domestic power cords ◆ (2) European power cords

◆ (3) International power plug adapters ◆ Documentation, warranty, and software

license agreement

1-6	Unpacking and Assembly

Image 18

HP 0706124 REV B manual Parts List

Contents

DisplayMaker Legacy Mach Part Number 0706124 Rev B Legal notices Iii Revision Log Release Date Description Regulatory Statements DOC Canada Telecommunications Network Statement About This Manual Vii Vorsicht ConventionsHinweis Viii Table of Contents Installing Ink and Media Table of ContentsMeasure Media Width Technical Specifications Calibrating the PrinterMaintaining the Printer Troubleshooting IndexXii Getting Started Getting Started Operating Requirements Electrical EnvironmentalOperating Requirements Important Operating Notes Operating Requirements Safety Warnings Warnung Bewegliche Teile, Verletzungsgefahr Unpacking and Assembly Unpacking and Assembly Parts List Stand assembly Remove the red-headed bolts Locate the assembly supports ➍ Roll the printer onto its back Tower of the support is now at the front of the pallet Unpacking and Assembly Unpacking and Assembly Unpacking and Assembly Connecting to the Print Server Power-Up Sequence What’s Next? Server sends the image to the printer for printing Workflow OverviewPrint server RIPs the job Workflow Overview Parts Overview Parts Overview Index Description Transport chain not shown supports the ink supPinch rollers 12 places grip the media during Ink reservoir tray two places holds ink reservoir boxes Printhead carriage, printhead covers open Special Features Performance Features Ease-Of-Use Features Special Features Using the Control Panel Overview Front Navigation Keys Menu Menu Tree Ready Status Screen Front Menu OverviewReady Screen Front Menu Overview Overview Tip Front Front Media info, ink info screens Front Front Front Lighted menu options Navigation KeysKey Description Navigation Keys Menu Menu Print Settings Page Printer Options Job. This conserves media and speeds printing by Features to group separate print jobs into a singleUse the ColorSpan print server’s MediaSaver or N-Up Eliminating the blank space between jobs, without Reset All Defaults Service Printer User Diagnostics Service Tests Measure Media Width CalibrationsHome Head New Carriage Disable Media Sensor Menu Tree Front Calibrate PrinterMenu Tree Configure Printer Service Printer Service Tests Calibrations Menu Tree Installing Ink and Media Installing Ink and Media Variable Mode Printing Variable Mode Printing Variable Mode Printing Ink System Overview Ink System Overview Ink type and ink number labels Ink System Overview To clean a printhead with jet-outs, see Cleaning Ink Jets onPrinthead Handling Tips Selecting a Print Mode Six-color ink sets Four-color ink setsPress the Proceed key Selecting a Print Mode Printhead Positions Ink ColorsInk Type Suffix Press the and keys to select the color map you will use Press to continue Switching Between Ink Sets Switching Between Ink Sets Switching Between Ink Sets Installing Ink for the First Time in a New Printer Installing Ink for the First Time in a New Printer Placing the drain bottle This will allow air to escape from the supply tube Install the printhead into the carriage Installing Ink for the First Time in a New Printer Replacing Ink System Components Replacing an Ink Reservoir During Printing Hot Swapping Replacing Ink System Components Install the new printhead into the carriage Press the Carriage button Replacing An Ink Tube Replacing Ink System Components 13. Connecting the ink tube to the reservoir Reconnecting the ink tube to the ink reservoir Head to fail. This condition may be recoverable byIf the ink does not begin flowing, try disconnecting Necting it to a printhead. Attempting to print with an Loading Media Tip For best results, use genuine ColorSpan media Edges of the media, so it is not necessary to align Load and secure the other collet against end of media rollPrinter automatically locates the right and left Media edges to a reference mark on the platen Press the key to proceed Control panel asks whether you want to use the takeup system If necessary, a cardboard core from a roll of masking Width when attached to the takeup spool. EnsureHas some media on it will change the weight Or other graphic arts tape can be slipped over Loading Media Loading Media Relative Humidity Printer Action Cutting and Unloading Media Cutting and Unloading Media Calibrating the Printer Calibrating the Printer AutoSet Manual Calibrations Manual Calibrations Following prompt appears Adjust the media feed advance using the control panel Inch/12-inch Calibration Double Lines Calibration Fine Medium Coarse Cancel CalibrationExamine the patterns with a high-power mangifier Select a pattern and press the key to proceed Manual calibration see AutoSet on page 4-2 for AutoSet incorporates an automatic version of thisCalibration. Try AutoSet first before running this Details Printer prints the calibration pattern you selected Repeat steps 12 through 14 for each of the twelve heads Press the key Press the and keys to select a pattern, then press the key 19. Head-to-Head Registration patterns Repeat steps 10 through 12 for each of the heads Repeat steps 15 through 17 for each of the Y patterns Sometimes can be recovered by carefully wiping For best results, before performing this procedureClean the printhead jets as described in Cleaning Ink Jets on page 5-3. Autodetected missing jets 21. Sample jet mapping pattern Report Individual Bad Jets Press and to select a head number, then press Proceed When you are finished reporting bad jets, press Clear Individual Bad JetsView Current Bad Jets Clear All Bad Jets PressPress Repeat steps 7 through Jet Status Lines Zero Registration Data Auto Calibrations Auto Calibrations Quality Check Mode AutoTuneAutoTune Calibration Summary Jets Unfixed CP Codes Patches are dry before taking readings. Use LinearizationFor best results, be sure that the linearization Printer’s dryer with heat to ensure complete drying Linearization Maintaining the Printer Maintaining the Printer Action Interval When printing interval warning appearsMaintenance Schedule Interval Daily Cleaning Ink Jets Maintenance interval dailyCleaning Ink Jets Cleaning Ink Jets Boots Wipers Cleaning the Service Station Cleaning the Service Station Maintenance interval as needed Printing Prime BarsPrinting Prime Bars Manual Priming Manual Priming Manual Priming Cleaning the Top Cover Cleaning the Top Cover Purging the Printheads Purging the Printheads Purging the Printheads Cleaning the Encoder Encoder and rail Maintenance interval at Maintenance Clock Alarm Cleaning the Carriage Rail Technical Specifications Technical Specifications Specifications General Specifications Mode Color Set Print Speed Resolution PerformancePrint Modes Supplies and Accessories Supplies and Accessories Troubleshooting Troubleshooting Does the printer’s power come ON? Troubleshooting Checklist Troubleshooting Checklist Diagnostics Diagnostics Code, Message Cause Recovery DiagnosticsTable B-1. Actions and Warnings MS Media Sensing PC Printing Calibrations PG Purge SS Service StationPD Primer Door SC System Calibrations VN VideoNet WP White Point Banding Stitch Banding Edge BandingBanding Banding Texture Banding Swath Edge Banding Page Index Index-1 Index-2 Dryer 1-21,2-13,3-31 Index-3 Index-4 Index-5 Index-6