Special Features | HP 0706124 REV B specs

Special Features

Performance Features

Ease-Of-Use Features

The printer has many advanced features to help you produce the best printed output with the least effort.

◆AutoSet Calibration — uses a high-resolution digital imag- ing sensor to automatically align printheads in the x-y directions and bidirectionally for precise positioning of ink jet pixels, also compensates for lost or misfiring jets by using substitute jets without slowing printing speed.

◆AutoTune — can run AutoSet at user-defined intervals, for highest quality during unattended printing. Optionally, if print quality falls below a user-defined level, printing stops until the problem is corrected.

◆Onboard linearization — uses the onboard photodiode to linearize output over the entire density range (with print server or RIP support).

◆Integrated heated dryer — dries output as it prints. Option- ally, the dryer fan may be turned off to avoid streaking on poly and film media.

◆Humidity sensor — slows printing in high humidity condi- tions to ensure drying, and alerts the user when the ambi- ent humidity is outside of optimal range.

◆Modular ink delivery system — the ink system consists of three components—ink reservoir, ink tube, printhead—each of which can be replaced independently of the others as needed.

◆Tilt-upprint-head carriage — printhead carriage tilts up for easy access to the ink tubes, printheads, and image sensors.

◆Manual priming system — recovers clogged ink jets without removing the printhead from the printer.

◆Manual air purging system — recovers printheads that are disabled due to too much air being introduced.

◆Integrated bidirectional takeup system — takes up printed output onto a spool for extended unattended printing. Out- put may be wound image-side out or image-side in.

◆Media width sensing — automatically detects the width and position of the media loaded, for precise image placement.

◆Simplified control panel interface — Front Page screen pre- sents frequently-used functions, with recommended preset configurations. A menu provides access to less-frequently used functions and troubleshooting help.

Special Features

1-21

Image 33

HP 0706124 REV B manual Special Features, Performance Features Ease-Of-Use Features

Contents

Part Number 0706124 Rev B DisplayMaker Legacy Mach Legal notices Iii Release Date Description Revision Log DOC Canada Regulatory Statements Telecommunications Network Statement Vii About This Manual Hinweis ConventionsVorsicht Viii Table of Contents Installing Ink and Media Table of ContentsMeasure Media Width Technical Specifications Calibrating the PrinterMaintaining the Printer Troubleshooting IndexXii Getting Started Getting Started Operating Requirements Electrical EnvironmentalOperating Requirements Operating Requirements Important Operating Notes Warnung Bewegliche Teile, Verletzungsgefahr Safety Warnings Unpacking and Assembly Unpacking and Assembly Parts List Stand assembly Remove the red-headed bolts Locate the assembly supports ➍ Roll the printer onto its back Tower of the support is now at the front of the pallet Unpacking and Assembly Unpacking and Assembly Unpacking and Assembly Connecting to the Print Server Power-Up Sequence What’s Next? Print server RIPs the job Workflow OverviewServer sends the image to the printer for printing Workflow Overview Parts Overview Parts Overview Index Description Transport chain not shown supports the ink supPinch rollers 12 places grip the media during Ink reservoir tray two places holds ink reservoir boxes Printhead carriage, printhead covers open Performance Features Ease-Of-Use Features Special Features Special Features Overview Front Navigation Keys Menu Menu Tree Using the Control Panel Ready Screen Front Menu OverviewReady Status Screen Front Menu Overview Overview Tip Front Front Front Media info, ink info screens Front Front Key Description Navigation KeysLighted menu options Navigation Keys Menu Menu Print Settings Page Printer Options Use the ColorSpan print server’s MediaSaver or N-Up Features to group separate print jobs into a singleJob. This conserves media and speeds printing by Eliminating the blank space between jobs, without Reset All Defaults Service Tests Service Printer User Diagnostics Home Head CalibrationsMeasure Media Width New Carriage Disable Media Sensor Menu Tree Front Calibrate PrinterMenu Tree Configure Printer Service Printer Calibrations Service Tests Menu Tree Installing Ink and Media Installing Ink and Media Variable Mode Printing Variable Mode Printing Variable Mode Printing Ink System Overview Ink System Overview Ink System Overview Ink type and ink number labels To clean a printhead with jet-outs, see Cleaning Ink Jets onPrinthead Handling Tips Selecting a Print Mode Six-color ink sets Four-color ink setsPress the Proceed key Selecting a Print Mode Printhead Positions Ink ColorsInk Type Suffix Press to continue Press the and keys to select the color map you will use Switching Between Ink Sets Switching Between Ink Sets Switching Between Ink Sets Installing Ink for the First Time in a New Printer Placing the drain bottle Installing Ink for the First Time in a New Printer This will allow air to escape from the supply tube Install the printhead into the carriage Installing Ink for the First Time in a New Printer Replacing Ink System Components Replacing Ink System Components Replacing an Ink Reservoir During Printing Hot Swapping Press the Carriage button Install the new printhead into the carriage Replacing An Ink Tube Replacing Ink System Components 13. Connecting the ink tube to the reservoir If the ink does not begin flowing, try disconnecting Head to fail. This condition may be recoverable byReconnecting the ink tube to the ink reservoir Necting it to a printhead. Attempting to print with an Tip For best results, use genuine ColorSpan media Loading Media Printer automatically locates the right and left Load and secure the other collet against end of media rollEdges of the media, so it is not necessary to align Media edges to a reference mark on the platen Press the key to proceed Control panel asks whether you want to use the takeup system Has some media on it will change the weight Width when attached to the takeup spool. EnsureIf necessary, a cardboard core from a roll of masking Or other graphic arts tape can be slipped over Loading Media Loading Media Relative Humidity Printer Action Cutting and Unloading Media Cutting and Unloading Media Calibrating the Printer Calibrating the Printer AutoSet Manual Calibrations Manual Calibrations Following prompt appears Inch/12-inch Calibration Adjust the media feed advance using the control panel Examine the patterns with a high-power mangifier Fine Medium Coarse Cancel CalibrationDouble Lines Calibration Select a pattern and press the key to proceed Calibration. Try AutoSet first before running this AutoSet incorporates an automatic version of thisManual calibration see AutoSet on page 4-2 for Details Printer prints the calibration pattern you selected Repeat steps 12 through 14 for each of the twelve heads Press the and keys to select a pattern, then press the key Press the key 19. Head-to-Head Registration patterns Repeat steps 15 through 17 for each of the Y patterns Repeat steps 10 through 12 for each of the heads Clean the printhead jets as described in Cleaning For best results, before performing this procedureSometimes can be recovered by carefully wiping Ink Jets on page 5-3. Autodetected missing jets 21. Sample jet mapping pattern Press and to select a head number, then press Proceed Report Individual Bad Jets When you are finished reporting bad jets, press Clear Individual Bad JetsView Current Bad Jets Clear All Bad Jets PressPress Repeat steps 7 through Jet Status Lines Zero Registration Data Auto Calibrations Auto Calibrations Quality Check Mode AutoTuneAutoTune Calibration Summary CP Codes Jets Unfixed For best results, be sure that the linearization LinearizationPatches are dry before taking readings. Use Printer’s dryer with heat to ensure complete drying Linearization Maintaining the Printer Maintaining the Printer Maintenance Schedule Interval When printing interval warning appearsAction Interval Daily Cleaning Ink Jets Maintenance interval dailyCleaning Ink Jets Cleaning Ink Jets Cleaning the Service Station Boots Wipers Cleaning the Service Station Maintenance interval as needed Printing Prime BarsPrinting Prime Bars Manual Priming Manual Priming Manual Priming Cleaning the Top Cover Cleaning the Top Cover Purging the Printheads Purging the Printheads Purging the Printheads Encoder and rail Cleaning the Encoder Cleaning the Carriage Rail Maintenance interval at Maintenance Clock Alarm Technical Specifications Technical Specifications General Specifications Specifications Mode Color Set Print Speed Resolution PerformancePrint Modes Supplies and Accessories Supplies and Accessories Troubleshooting Troubleshooting Troubleshooting Checklist Does the printer’s power come ON? Troubleshooting Checklist Diagnostics Diagnostics Code, Message Cause Recovery DiagnosticsTable B-1. Actions and Warnings PC Printing Calibrations MS Media Sensing PD Primer Door SS Service StationPG Purge SC System Calibrations WP White Point VN VideoNet Banding Stitch Banding Edge BandingBanding Banding Texture Banding Swath Edge Banding Page Index-1 Index Index-2 Index-3 Dryer 1-21,2-13,3-31 Index-4 Index-5 Index-6