Installing an Interface Cable for Printing
| The user must purchase separately a shielded Centronics | |
| to connect the HP OfficeJet Series 300 to his computer for printing. He or she can use | |
| C2950A (2 meter) or the HP C2951A (3 meter) Centronics parallel cable. See chapter 1of | |
| this guide for ordering information. | |
1 | Make sure the computer is turned off by pressingPlacethe HP OfficeJet Series 300 on a stable | |
| 2 | |
| “O ” on the On/Off switch (located on the leftsurfaceside at a safe distance from the edge. The | |
| of the machine’s base). Then remove the outputandrotate it on its side so that the bottom o | |
| tray from the HP OfficeJet Series 300 and setunit faces the user as shown below. Connect t | |
| aside. | printer end* of the interfacefirmlycab toe the |
|
| interface port on the HP OfficeJet. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Output Tray |
| * The printer endof the interface cable has | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| notches, andcomputerthe | endhas screws. | |||||||||||
| SL6 | SL54 |
|
|
| |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
3 | Snap both clips into the notches on the connectorReturnthe HP OfficeJet Model Series 300 to its | |||||||||||||||||||||||||||
as shown. | 4 | upright position, making sure it does not rest | ||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| the interface cable. Insert the output tray. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Now connect computerthe | endof the interface |
cable to the parallel (LPT 1) port on the | |
computer and tighten the screws on the | |
connector (not shown). | |
SL31 | SL51 |